Home » TEAC Manuals » Audio Mixers » TEAC DP-24 » Manual Viewer

TEAC DP-24 DP-24 Owner's Manual - Page 84

Using CDs, Using the CD drive, Preparations before using CDs with this unit

Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

14 - Using CDs Using the CD drive This unit has a CD drive that supports writing to CD-R and CD-RW discs. In addition to playing back Audio CDs (CDDA), the unit's CD drive can also be used for the following purposes. •• Create an Audio CD from the master file. •• Import tracks from Audio CDs into the current song. CAUTION When creating a CD from a master file, set to 44.1kHz, 16bit to create a song. Preparations before using CDs with this unit When using CDs with this unit, make the following preparations. •• Before using a CD, change the recorder mode to Multi Track. In modes other than Multi Track, you cannot open the CD menu screen. In Mixdown or Mastering mode, press the MIXDOWN/MASTERING button repeatedly until the unit switches to Multi Track mode. In Bounce mode, press the BOUNCE button to switch to the Multi Track mode. •• Open the CD menu screen before inserting or ejecting a CD. In order to prevent the sound of the CD drive being operated during recording, for example, the power to the drive is disabled when in modes other than CD mode. For this reason, it is necessary to put the unit into CD mode in order to load or eject a CD. Even in CD mode, a CD cannot be loaded or ejected after being mounted. (Except for CD menu screen) Since CD mounting is canceled in screens other than CD menu screen, load or eject a CD in the CD menu screen or CD PLAYER screen. Types of CDs that can be used with this unit This unit is compatible with 12-cm and 8-cm CD, CD-R, CD-RW and CD-RW High Speed discs. This unit does not support CD-RW Ultra Speed or CD-RW Ultra Speed+ discs. For the functions that can be used with discs and the types of compatible discs, see "Media Compatibility Table" on page 91. ªª Writing to an already written CD-RW With this unit, you do not need to erase a CD-RW beforehand. You can use a previously written CD-RW by erasing it at the beginning of the desired operation. When creating an Audio CD, the following message will appear if you load an already written CD-RW disc. Confirmation message Press the F2 (Yes) button to erase the songs recorded on the disc. If you do not want to erase the CD-RW disc, press the F1 (NO) button. The disc tray will open slightly. Pull the tray out and replace the disc with another one. CAUTION If you use Track At Once to write a master file to an unfinalized CD-RW in Audio CD format (a CD-RW created by selecting a single master file on the MASTER WRITE screen and setting FINALIZE to OFF), the file will be added without showing the CD-RW erasure warning, and it will not overwrite existing data on the disc. 84 TASCAM DP-24

Section	Page
1 – Introduction	8
Features	8
Items included with the product	8
Conventions used in this manual	8
Intellectual property rights	9
Precautions for placement and use	9
Beware of condensation	9
Cleaning the unit	9
About SD cards	9
Precautions for use	10
About CDs (Compact Discs)	10
Precautions for use	10
About CD-R and CD-RW discs	10
2 - Quick Guide	12
Playback and mixing	12
Preparation	12
Listening to the demo song	13
Recording and mastering	14
Creating a new song	14
Connecting and setting the input sources	15
Setting the guitar as the recording source for TRACK 1	15
Adjusting and monitoring the input level	15
Recording a guitar to TRACK 1	16
Playing back the recording	16
Recording a guitar to TRACK 2	16
Recording a vocal to TRACK 3	17
Mixing the tracks	18
Mastering a recording	19
Creating an audio CD with the master file	21
Inserting a CD	21
Writing to a CD-R/CD-RW	22
Ejecting a CD	23
Shutting down	23
3 – Names and Functions of Parts	24
Top panel	24
Front panel	28
Rear panel	29
Home screen	30
Menu structure	31
Screen operations	32
4 – Preparation	34
Inserting and removing SD cards	34
Inserting an SD card	34
Removing the card	34
About write-protected SD cards	34
Powering the unit	34
Start-up & Shutdown	35
Starting up the unit	35
Shutting down	35
Setting the date and time	35
Preparing an SD card for use	36
Recorder modes	36
Connecting other equipment	36
Front panel	36
Rear panel	37
Adjusting the contrast	37
5 - Song Management	38
Editing names	38
Loading a song	38
Creating a new song	38
Saving a song	39
Viewing song information	40
Copying songs	40
Erasing songs	41
Protecting songs	41
Deleting unnecessary audio data from a song	42
Changing a song name	43
6 - Basic Recording	44
Selecting the input sources	44
Assigning inputs	44
Assigning to a mono track	44
Assigning to a stereo track	44
Assigning to a stereo bus	44
Checking the assignment	45
Canceling an assignment	45
Using phantom power	45
Monitoring	45
Monitor selection	45
OL indicators and level meters	46
Setting the Mixer screen	46
Using EQ (equalizer)	46
DIGITAL TRIM setting (Track only)	47
Built-in Send Effects and External Effects	47
Setting built-in effects	47
Setting the stereo position	48
Changing the signal phase	48
Checking the fader level	48
Solo	48
Muting tracks	48
Rehearsing the recording	49
Making the first recording	49
Multitrack recording	50
Setting the tracks for recording	50
Setting track pan and level	50
Input selection and assignment	50
Setting input levels	50
Recording	50
Undoing an operation	50
Setting the undoing feature	50
Undoing the last operation (single undo)	51
Undoing previous operations (multi-undo)	51
7 - Recorder Functions	52
Punching in and out	52
Using a foot switch to punch in/out	52
Setting the foot switch	52
Bouncing tracks	53
Performing the track bouncing	53
Checking the result	53
Direct Location Function	54
Locating directly a specified time	54
Locating directly a specified measure/beat	54
Location marks	54
Setting a location mark	54
Skipping to location marks	55
Deleting a location mark	55
Returning to zero (TO ZERO) and returning to last recording position (TO LAST REC)	55
Fast forward/rewind search	55
Jog positioning	55
Viewing the track's waveform	55
Listening to the track sounds	55
Repeat playback	56
Setting IN/OUT points	56
Using repeat playback	56
Moving back a few seconds for replay (jump back playback)	56
Checking cueing points (preview)	57
Auto punch in/out	57
Setting punch in/out points	58
Checking punch in/out points	58
Rehearsing punch in/out	58
Performing auto punch in/out	59
Checking a take	59
Virtual tracks	59
8 - Track Editing	60
Overview of track editing	60
Editing points	60
Basic editing procedures	60
Explanation of items	60
COPY/PASTE	61
COPY/INSERT	61
MOVE/PASTE	62
MOVE/INSERT	62
OPEN (Insert Silence)	62
CUT (Remove Part)	62
SILENCE (Erase Part)	63
CLONE TRACK (Track Duplication)	63
CLEAN OUT (Delete Track)	63
9 - Using Built-In Effects	64
Dynamic effects	64
Inserting a dynamic effect	64
Editing a dynamic effect	64
Guitar effects	64
Inserting a guitar effect	64
Editing guitar effects	65
Calling effects from the guitar effect library	65
Saving guitar effects in the library	65
Send effects	65
Using send effects	65
Editing send effects	65
Calling the send effect library	66
Saving send effects in the library	66
10 - Mixing Down and Mastering Tracks	68
Mixing down tracks	68
Levels and balance	68
Fader group	68
Stereo position (panning)	68
TRACK EQ (equalizer)	68
Send effects	69
Creating a master file	69
Setting the start and end points	69
Creating a master file	70
Exiting Mixdown mode	70
Checking the master file	70
Ending master file checking	71
Finishing up a master file (mastering)	71
Mastering procedures	71
Using the mastering EQ (equalizer)	71
Using mastering compression	72
Using normalize	73
Using the noise shaper (Noise Shaped Dithering)	73
Exiting Mastering mode	73
11 - Various Other Functions	74
Metronome	74
MIDI Sync	74
MIDI remote control	75
Tuner function	75
Setup (PREFERENCE)	76
Auto Monitor	76
Restoring the initial preference settings	77
Viewing information	77
12 - SD Card Management	78
Quick formatting an SD card	78
Full formatting an SD card	79
13 - Exchanging Data with a Computer	80
Operating system requirements	80
Connecting to a computer	80
Disconnecting	81
Track import and export	82
Importing tracks	82
Exporting tracks	83
Deleting files from the AudioDepot folder	83
14 - Using CDs	84
Using the CD drive	84
Preparations before using CDs with this unit	84
Types of CDs that can be used with this unit	84
Loading and ejecting CDs	85
Loading a CD	85
Ejecting a CD	86
Forcing disc ejection	86
Playing back an Audio CD	86
Creating an Audio CD	87
Using Disc At Once	87
Using Track At Once	88
Using LIVE WRITER	89
Finalizing a CD	90
Importing songs from an Audio CD	90
Erasing a CD-RW	91
Media Compatibility Table	91
15 – Troubleshooting	92
16 – Messages	93
General messages	93
CD mode messages	95
CD-related error messages	96
17 – Specifications	97
Ratings	97
Input/output ratings	97
Analog audio input/output ratings	97
Control input/output ratings	97
Audio performance	97
Operating requirements	97
Dimensional drawings	98
General	98
Block diagram	99
Level diagram	100
18 – Appendix	101
MIDI Control Change message	101
Mixer control change parameters	101
MIDI Program Change message	102
Dynamic effects	102
Preset libraries of the send effects	102
Preset libraries of the guitar effects	102
MIDI Implementation Chart	103

Match case Limit results 1 per page

TASCAM DP-24

14 - Using CDs

Using the CD drive

This unit has a CD drive that supports writing to CD-R and

CD-RW discs. In addition to playing back Audio CDs (CD-

DA), the unit's CD drive can also be used for the following

purposes.

Create an Audio CD from the master file.

•

Import tracks from Audio CDs into the current song.

•

CAUTION

When creating a CD from a master file, set to

44.1kHz

16bit

to create a song.

Preparations before using CDs with

this unit

When using CDs with this unit, make the following

preparations.

Before using a CD, change the recorder mode to

•

Multi Track

. In modes other than

Multi

Track

, you cannot open the

menu screen.

Mixdown

Mastering

mode, press the

MIXDOWN/MASTERING

button repeatedly until the

unit switches to

Multi Track

mode.

Bounce

mode, press the

BOUNCE

button to switch

to the

Multi Track

mode.

Open the

•

menu screen before inserting or ejecting

a CD.

In order to prevent the sound of the CD drive being

operated during recording, for example, the power

to the drive is disabled when in modes other than CD

mode. For this reason, it is necessary to put the unit

into CD mode in order to load or eject a CD. Even in CD

mode, a CD cannot be loaded or ejected after being

mounted. (Except for

menu screen)

Since CD mounting is canceled in screens other than

menu screen, load or eject a CD in the

screen or

CD PLAYER

screen.

Types of CDs that can be used with

this unit

This unit is compatible with 12-cm and 8-cm CD, CD-R,

CD-RW and CD-RW High Speed discs. This unit does not

support CD-RW Ultra Speed or CD-RW Ultra Speed+ discs.

For the functions that can be used with discs and the

types of compatible discs, see "Media Compatibility Table"

on page 91.

Writing to an already written CD-RW

With this unit, you do not need to erase a CD-RW

beforehand. You can use a previously written CD-RW by

erasing it at the beginning of the desired operation.

When creating an Audio CD, the following message will

appear if you load an already written CD-RW disc.

Confirmation message

Press the

F2 (

Yes

)

button to erase the songs recorded on

the disc.

If you do not want to erase the CD-RW disc, press the

(

)

button. The disc tray will open slightly. Pull the tray

out and replace the disc with another one.

CAUTION

If you use Track At Once to write a master file to an

unfinalized CD-RW in Audio CD format (a CD-RW created

by selecting a single master file on the

MASTER WRITE

screen and setting FINALIZE to OFF), the file will be added

without showing the CD-RW erasure warning, and it will

not overwrite existing data on the disc.