TEAC HD-P2 HD-P2 Quick Start Guide - Page 2

Play Audio, Set Up Default Project Settings, Set Up Project Templates, Input Settings, Top Panel

Get TEAC HD-P2 PDF manuals and user guides View all TEAC HD-P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Set Up Default Project Settings 1. Press the MENU key 2. Use the DATA wheel to scroll to System Menu 3. Press the SELECT key 4. Use the DATA wheel to scroll to Default Project Settings 5. Press the SELECT key 6. Use the DATA wheel to scroll to the desired setting to change 7. Press the SELECT key, change the setting, press the SELECT key again 8. Repeat Step 7 for all desired settings NOTE All newly created projects will use these settings unless a user defined project template is used. Set Up Project Templates 1. Press the MENU key 2. Use the DATA wheel to scroll to Project Menu 3. Press the SELECT key 4. Use the DATA wheel to scroll to Save as Project Template 5. Press the SELECT key 6. Name your project template and Save NOTE • This will save the system settings (excluding recorded audio and markers) of the currently loaded project as a project template. • A list of currently available project templates is available under the System Menu where they can be renamed or deleted. 2 Input Settings This is a two part operation consisting of top panel switch settings and menu settings. Top Panel • Set the LEFT INPUT and RIGHT INPUT switches to LINE or MIC. When set to LINE, the HD-P2 accepts analog input from the appropriate RCA jack. When set to MIC, the HD-P2 accepts analog input from the appropriate XLR jack. Note that one side (Left or Right) can accept input from only one analog source at a time. These settings for Left and Right are independent of each other. • Set the MIC switch to INT to use the built-in mono microphone or EXT to use microphones connected to the XLR inputs. • Enable PHANTOM if microphones are connected to the XLR inputs that require phantom power. • Enable the LEFT and/or RIGHT -20dB PAD if recording from a particularly loud source. This is only for the XLR inputs. • Enable LOW CUT if there is undesirable low frequency energy present such as traffic or air conditioning rumble. This introduces an analog filter at 100Hz. • Enable LIMTER to protect against unexpected transients from overloading the D/A converters. The STEREO LINK switch, when enabled, causes the limiter to engage on both channels when only one channel receives loud input. Otherwise loud input on one channel will not trigger the limiter on the other channel. Menus The Left/Right input source can be selected between Analog and S/PDIF. This setting cannot be made independently for the Left & Right channels. There are two places where this setting can be selected: 1. Within the currently loaded project's Settings menu:

  • 1
  • 2
  • 3
  • 4
2
Set Up Default Project Settings
1. Press the
MENU
key
2. Use the
DATA
wheel to scroll to
System Menu
3. Press the
SELECT
key
4. Use the
DATA
wheel to scroll to
Default
Project Settings
5. Press the
SELECT
key
6. Use the
DATA
wheel to scroll to the desired
setting to change
7. Press the
SELECT
key, change the setting,
press the
SELECT
key again
8. ±epeat Step 7 for all desired settings
NOTE
All newly created projects will use these
settings unless a user defined project template
is used.
Set Up Project Templates
1. Press the
MENU
key
2. Use the
DATA
wheel to scroll to
Project Menu
3. Press the
SELECT
key
4. Use the
DATA
wheel to scroll to
Save as
Project Template
5. Press the
SELECT
key
6. Name your project template and Save
NOTE
•
This will save the system settings (excluding
recorded audio and markers) of the currently
loaded project as a project template.
•
A list of currently available project templates
is available under the System Menu where
they can be renamed or deleted.
Input Settings
This is a two part operation consisting of top panel
switch settings and menu settings.
Top Panel
•
Set the
LEFT INPUT
and
RIGHT INPUT
switches
to
LINE
or
MIC
. When set to
LINE
, the HD-P2
accepts analog input from the appropriate
RCA jack. When set to
MIC
, the HD-P2
accepts analog input from the appropriate XLR
jack. Note that one side (Left or Right) can
accept input from only one analog source at
a time. These settings for Left and Right are
independent of each other.
•
Set the
MIC
switch to
INT
to use the built-in
mono microphone or
EXT
to use microphones
connected to the XLR inputs.
•
Enable
PHANTOM
if microphones are
connected to the XLR inputs that require
phantom power.
•
Enable the
LEFT
and/or
RIGHT
-20dB PAD
if
recording from a particularly loud source. This
is only for the XLR inputs.
•
Enable
LOW CUT
if there is undesirable low
frequency energy present such as traffic or air
conditioning rumble. This introduces an analog
filter at 100Hz.
•
Enable
LIMTER
to protect against unexpected
transients from overloading the D/A converters.
The
STEREO LINK
switch, when enabled,
causes the limiter to engage on both channels
when only one channel receives loud input.
Otherwise loud input on one channel will not
trigger the limiter on the other channel.
Menus
The Left/Right input source can be selected between
Analog and S/PDIF. This setting cannot be made
independently for the Left & Right channels. There
are two places where this setting can be selected:
1. Within the currently loaded project’s
Settings menu: