TEAC IF-SM/DM IF-SM:DM Owner's Manual - Page 6

Using the card : OPERATION option

Get TEAC IF-SM/DM PDF manuals and user guides View all TEAC IF-SM/DM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

2 - Using the card : OPERATION option Soloing channels This works with the same SHIFTed number keys as for muting (see Figure 2.3, SHIFTed number keys used for channel control) as well as the cursor and ENTER key options. There are two solo options-one for an exclusive solo mode, where only one channel at a Downmix on/off Use the on-screen DOWN MIX button to turn downmixing on and off (as set up in the DOWN MIX option) - ignored when the alternative Bass management Use the on-screen BASS MGT button to turn bass management on and off (as set up in the BASS MANAGEMENT option) - ignored when Alternative speakers This routes the signal when downmixed to stereo, to the speakers connected to the LC and RC channels, which are not used in the surround patterns. Oscillator routing Allows the routing of the mixer's internal oscillator to the surround card outputs. When the oscillator is routed in this way, soloing is automatically changed to exclusive To 2.1 When on and the current surround mode is 5.1 or 6.1, this setting automatically overrides the current downmix setting (of course, downmix is not possible when this switch is on). USE ST-FADER If you check "USE ST-FADER", you can adjust the Monitor level settings by the Stereo fader. SPL reference and level Note that the SPL REFERENCE setting and monitor level settings are made on this page. These 6 TASCAM IF-SM/DM Owner's Manual time is active, and one for a mixed solo mode, where selected channels are active. The on-screen solo marks are shown by an S button, in the same way as the mute buttons are shown by an M (they invert when active, etc.). speaker switch, 2.1 switch or oscillator switch are on. the alternative speaker switch, 2.1 switch or oscillator switch are on. This allows the use of a pair of "large" stereo speakers together with smaller surround monitors, without the need for repatching. Naturally, downmix is not possible with this switch on. soloing (it reverts to the previous setting when the oscillator is not routed in this way). Note that downmix and bass management are not available when the oscillator is routed in this way. When this setting is deactivated, the original downmix and mode are restored, as is the mute status of the LFE channel. are explained further in "MONITOR ALIGNMENT option" on page 14.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
2 – Using the card : OPERATION option
6
TASCAM IF-SM/DM Owner’s Manual
Soloing channels
This works with the same
SHIFT
ed number
keys as for muting (see Figure 2.3,
SHIFTed
number keys used for channel control
) as well
as the cursor and
ENTER
key options.
There are two solo options—one for an exclu-
sive solo mode, where only one channel at a
time is active, and one for a mixed solo mode,
where selected channels are active.
The on-screen solo marks are shown by an
S
button, in the same way as the mute buttons are
shown by an
M
(they invert when active, etc.).
Downmix on/off
Use the on-screen
DOWN MIX
button to turn
downmixing on and off (as set up in the
DOWN
MIX
option) — ignored when the alternative
speaker switch, 2.1 switch or oscillator switch
are on.
Bass management
Use the on-screen
BASS MGT
button to turn
bass management on and off (as set up in the
BASS MANAGEMENT
option) — ignored when
the alternative speaker switch, 2.1 switch or
oscillator switch are on.
Alternative speakers
This routes the signal when downmixed to
stereo, to the speakers connected to the LC
and RC channels, which are not used in the
surround patterns.
This allows the use of a pair of “large” stereo
speakers together with smaller surround mon-
itors, without the need for repatching.
Naturally, downmix is not possible with this
switch on.
Oscillator routing
Allows the routing of the mixer’s internal
oscillator to the surround card outputs.
When the oscillator is routed in this way, solo-
ing is automatically changed to exclusive
soloing (it reverts to the previous setting when
the oscillator is not routed in this way).
Note that downmix and bass management are
not available when the oscillator is routed in
this way.
To 2.1
When on and the current surround mode is 5.1
or 6.1, this setting automatically overrides the
current downmix setting (of course, downmix
is not possible when this switch is on).
When this setting is deactivated, the original
downmix and mode are restored, as is the
mute status of the LFE channel.
USE ST-FADER
If you check “USE ST-FADER”, you can adjust
the Monitor level settings by the Stereo fader.
SPL reference and level
Note that the
SPL REFERENCE
setting and moni-
tor level settings are made on this page. These
are explained further in “MONITOR ALIGN-
MENT option” on page 14.