TEAC P-55-111 Instruction Manual - Page 33

Loading Print Media

Get TEAC P-55-111 PDF manuals and user guides View all TEAC P-55-111 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

SECTION 13 : Loading Print Media NOTES - The P-55 supports a standard medium (12-cm diameter) only. Mini media (8-cm diameter) and odd-shaped media are not supported. - With the P-55 you need to use the TEAC-specified media exclusively. Use of commercially available media for inkjet printers might inevitably result in poor quality output. 1) Press the LOAD/EJECT button to let the disc tray slide out. 2) Place a medium on the tray, label print side up, data committing side down. 3) Making sure that the medium is correctly placed on the tray, press the LOAD/EJECT button to let the tray slide in. 4) When the tray has fully slid in, the READY lamp will light up. Then, let the printing process start through graphics software in use. NOTES - Do not place any objects other than the right print media. - Load only one medium. Loading multiple media might produce trouble. - Load a medium only when the tray fully slides out and stops. - Make sure that the medium does not sit on the guide pins. Guide Pins - Clean dust off the medium surface before printing. (Printing on the medium with dust attached on the surface may deteriorate the original print quality.) WARNING - Do not touch the die-cast alloy part of the tray, which causes heat buildup. - Do not put your fingers or sleeves close to the tray that is sliding in or out. They can be got in, possibly causing injuries. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
33
SECTION 13 : Loading Print Media
NOTES
- The P-55 supports a standard medium (12-cm diameter) only. Mini media (8-cm diameter) and
odd-shaped media are not supported.
- With the P-55 you need to use the TEAC-specified media exclusively. Use of commercially
available media for inkjet printers might inevitably result in poor quality output.
1)
Press the
LOAD/EJECT
button to let the disc
tray slide out.
2)
Place a medium on the tray, label print side up,
data committing side down.
3)
Making sure that the medium is correctly placed
on the tray, press the
LOAD/EJECT
button to let
the tray slide in.
4)
When the tray has fully slid in, the READY lamp
will light up. Then, let the printing process start
through graphics software in use.
NOTES
- Do not place any objects other than the right print media.
- Load only one medium. Loading multiple media might produce trouble.
- Load a medium only when the tray fully slides out and stops.
- Make sure that the medium does not sit on the guide pins.
- Clean dust off the medium surface before printing.
(Printing on the medium with dust attached on the surface may deteriorate the original print quality.)
- Do not touch the die-cast alloy part of the tray, which causes heat buildup.
- Do not put your fingers or sleeves close to the tray that is sliding in or out.
They can be got in, possibly causing injuries.
WARNING
Guide Pins