TP-Link Archer VR400 Archer VR400EU V1 Quick Install Guide - Page 2

LED Indicators LED Status Indication Power On Flashing O System initialization complete. System initializing or firmware upgrading is in process. Do not disconnect or power off the modem router. Power is off. On DSL synchronization established. DSL Flashing DSL synchronization is in progress. O DSL synchronization failed. On Internet O Internet connection is available. No Internet connection or the modem router is operating in Bridge mode. Wireless On 2.4GHz O The 2.4GHz wireless radio band is enabled. The 2.4GHz wireless radio band is disabled. Wireless On 5GHz O The 5GHz wireless radio band is enabled. The 5GHz wireless radio band is disabled. On/O Turns On when a WPS synchronization is established and WPS automatically turns Off about five minutes later. Slow Flashing A wireless device is trying to connect to the network via WPS. This process may take up to 2 minutes. On LAN O The corresponding LAN port is connected. The corresponding LAN port is not connected. On The inserted USB device is identified and ready to use. USB Flashing A new USB device is being identified. O No USB device is plugged into the USB port. Note: The USB LED is on the rear panel of the router, near the USB port. Button Legend DSL LAN1 LAN2 LAN3 LAN4/WAN Button On/O Reset WPS Wi-Fi Indication Press to power on or o the modem router. Press and hold down for 8 seconds to reset the modem router into factory default settings. Press to start a WPS synchronization. Press to turn both 2.4GHz and 5GHz Wi-Fi on or o . Tether App To manage your network conveniently on your mobile device, scan the QR code to download the Tether App. Features Ethernet WAN Connection Connect an Ethernet cable (RJ45) from your fiber or cable modem to the LAN4/WAN port of the modem router to use it as a wireless router. Refer to the User Guide for wireless router configuration. 3G/4G Connectivity Connect a 3G/4G USB mobile broadband modem to the router's USB port to get wireless Internet access through 3G/4G mobile networks. The USB dongle can be con gured as the primary Internet connection, or as a backup to enhance network reliability. Refer to the User Guide for instructions. USB Features The USB port can also be used to share a printer, les and media from the USB storage device over your home network locally, or remotely through the Internet using its built-in FTP server capability. USB Port DSL Remote Access via FTP Server LAN1 LAN2 LAN3 LAN4/WAN Media Sharing Local Storage Sharing To learn more about the USB features, visit http://tp-link.com/app/usb or scan the QR code. Printer Sharing FAQ (Frequently Asked Questions) Q1. What can I do if the login page does not appear? A1. If the computer is set to a static or fixed IP address, change it to obtain an IP address automatically from the modem router. A2. Verify http://tplinkmodem.net is correctly entered in the web browser and press Enter. A3. Use another web browser and try again. A4. Reboot your modem router and try again. A5. Disable and enable the active network adapter. Q2. What can I do if the DSL LED does not turn solid on? A1. Check your cables and make sure they are all plugged in correctly, including the telephone lines and power adapter. A2. Restore your modem router to its factory default settings. A3. Remove the DSL splitter, directly connect the modem router to the phone jack and follow this Quick Installation to reconfigure the modem router. A4. Contact your ISP to verify if the DSL line is in good status. A5. If you have tried all the suggestions above and the problem still exists, contact our Technical Support. Q3. What can I do if I cannot access the Internet? A1. Make sure the telephone and Ethernet cables are plugged in correctly. A2. Try to log into the web management page of the modem router using the default address at http://tplinkmodem.net. If you can, try the following answers. If you cannot, change your computer to obtain an IP address automatically from the modem router. A3. Consult your ISP and make sure all the VPI/VCI (or VLAN ID), Connection Type, account username and password are correct. If they are not, please replace them with the correct settings and try again. A4. Restore the modem router to its factory default settings and reconfigure the modem router by following the instructions in this Quick Installation Guide. A5. Please contact our Technical Support if the problem still exists. Q4. What can I do if I forget my password? Web management page password: Restore the modem router to its factory default settings and then set a new password using 1-15 characters. Wireless Network password: A1. The default Wireless Password/PIN is printed on the product label of the modem router. A2. If the default wireless password has been changed, log into the modem router's web management page and go to Basic > Wireless to retrieve or reset your password. Q5. How do I restore the modem router to its factory default settings? A1. With the modem router powered on, press and hold down the Reset button on the rear panel of the modem router for 8 seconds until all LEDs turn on momentarily, then release the button. DSL Reset Button Press & Hold for 8 seconds LAN1 LAN2 LAN3 LA A2. Log in to the Web management page of the modem router, and go to Advanced > System Tools > Backup & Restore, click Factory Restore and wait until the reset process is complete. 7106506439 REV1.0.0 ©2016 TP-LINK