TP-Link N300 TD-W9977EU V1 Quick Installation Guide - Page 2

7106506525 REV1.0.0 ©2016 TP-LINK Configuring the Modem Router 1. Connecting your computer to the modem router (Wired or Wireless) Wired Connect the computer to your modem router and the LAN LED up. lights Ethernet cable Wireless a Find the SSID (network name) and Wireless Password printed on the product label at the bottom of the modem router. b Click the network icon of your computer or go to Wi-Fi Setting of your smart device, then select the SSID to join the network. Computer Connections are available Wireless Network Connection TP-LINK_XXXX √ Connect automatically Connect Smart Device 
Settings Wi-Fi OR Wi-Fi CHOOSE A NETWORK... TP-LINK_XXXX Other... 2. Configuring the modem router via a web browser A Launch a web browser and type in http://tplinkmodem.net or 192.168.1.1. Create a new password (1-15 characters) and click Save. Note: If the login page does not appear, please refer to FAQ > Q1. http://tplinkmodem.net New Password Low Middle High Confirm Password Save B Enter the new password that you created and click Log in. Note: For subsequent logins, use the password you have created. C Follow the step-by-step instructions of the Quick Setup to complete the initial configuration. Note: For advanced settings, please refer to the User Guide on our official website at www.tp-link.com. Tether App TP-LINK Tether app provides a simple, intuitive way to access and manage your router. You can block unwelcome devices, set up Parental Controls, configure your wireless settings and more. Scan the QR code to download the TP-LINK Tether app from the Apple App Store or Google Play. LED Indicators LED Power DSL Status Indication On Flashing Off System initialization is complete. System initializing or firmware upgrade is in progress. Do not disconnect or power off the modem router. Power is off. On DSL line is synchronized and ready to use. Flashing The DSL negotiation is in progress. Off DSL synchronization failed. On Internet Off Internet connection is available. No Internet connection or the modem router is operating in Bridge mode. Wireless On Off The 2.4GHz wireless radio band is enabled. The 2.4GHz wireless radio band is disabled. WPS On/Off Flashing Turns On when a WPS synchronization is established and automatically turns Off about five minutes later. A wireless device is trying to connect to the network via WPS. This process may take up to 2 minutes. LAN On The corresponding LAN port is connected. Off The corresponding LAN port is not connected. FAQ (Frequently Asked Questions) Q1. What can I do if the login page does not appear? A1. If the computer is set to a static or fixed IP address, change the computer's settings to obtain an IP address automatically from the modem router. A2. Verify http://tplinkmodem.net or 192.168.1.1 is correctly entered in the web browser and press Enter. A3. Use another web browser and try again. A4. Reboot your modem router and try again. A5. Disable and enable the active network adapter. Q2. What can I do if I cannot access the Internet? A1. Make sure the telephone and Ethernet cables are plugged in correctly. A2. Try to log in to the web management page of the modem router using the default address at http://tplinkmodem.net or 192.168.1.1. If you cannot, change your computer settings to obtain an IP address automatically from the modem router. If you can, try the steps below. A3. Consult your ISP and verify that the VPI/VCI (or VLAN ID), Connection Type, account username and password are correct. If they are not, please replace them with the correct settings and try again. A4. Restore the modem router to its factory default settings and reconfigure it by following the instructions in this guide. A5. Please contact our Technical Support if the problem persists. Q3. How do I restore the modem router to its factory default settings? A1. With the modem router powered on, press and hold down the Reset button on the rear panel of the modem router for 8 seconds until all LEDs turn back on momentarily, then release the button. Reset Button Press & Hold for 8 Seconds A2. Log in to the web management page of the modem router, and go to Advanced > System Tools > Backup & Restore, click Factory Restore and wait until the reset process is complete. Q4. What can I do if I forget my password? Web Management page password: Restore the modem router to its factory default settings and then create a new password using 1-15 characters. Wireless Network password: A1. The default Wireless Password/PIN is printed on the product label of the modem router. A2. If the default wireless password has been changed, log in to the modem router's web management page and go to Basic > Wireless to retrieve or reset your password. Q5. What can I do if the DSL LED does not turn solid on? A1. Check your cables and make sure they are all plugged in correctly, including the telephone lines and power adapter. A2. Manually change your DSL settings. Log in to the modem router's web management page, and go to Advanced > Network > DSL Settings. If you were in ADSL Mode, change the DSL Modulation Type to ADSL Auto Sync-up. If you were not sure about the mode, change to Auto Sync-up. Then click Save. You will be prompted a disconnection, and click YES to continue. A3. Restore your modem router to its factory default settings. A4. Remove the DSL splitter, directly connect the modem router to the phone jack and then reconfigure the modem router by following the instructions in this Quick Installation Guide. A4. Contact your ISP to check the status of your DSL line. A5. If the problem persists, contact TP-LINK's Technical Support.