TP-Link T3700G-52TQ T3700G-52TQUN V1 Installation Guide - Page 28

Con the Switch Using CLI

Get TP-Link T3700G-52TQ PDF manuals and user guides View all TP-Link T3700G-52TQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

JetStream Stackable L3 Managed Switch Figure 6-3 Main Page of the Switch 6.2 Configure the Switch Using CLI You can log in to the switch and access the CLI by the following two methods: ■■ Log in to the switch by the Console (USB) port or Console (RJ-45) port on the switch. ■■ Log in to the switch remotely by a Telnet or SSH connection through an Ethernet port. ■■ Logon by a Console Port The switch has two console ports: an RJ-45 console port and a Micro-USB console port. Console output is active on devices connected to both console ports, but console input is only active on one console port at a time. The Micro-USB connector takes precedence over the RJ-45 connector. Install the TP-Link USB Console Driver if you are using the USB serial port for the first time on a Windows-based PC. The driver can be found on the attached CD and Download page of our official website. Refer to the User Guide to learn more about the installation. To log in to the switch by the console port on the switch, please take the following steps: 1. Connect the PCs or Terminals to the console port on the switch by a provided cable. Refer to 5.3 Console Port to learn how to connect. 2. If you attach a PC, start the terminal emulation program (such as the Hypertermi-nal) on the PC. 3. Specify the connection COM port in the terminal emulation program. If the Micro-USB console port is used, you can view which COM port number is assigned to the USB serial port in the following path: Control Panel -> Hardware and Sournd -> Device Manager -> Ports -> USB Serial Port. 4. Configure the terminal emulation program or the terminal. You can use the default settings as follows: ■■ Baud rate: 38400 bps 24 Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
JetStream Stackable L3 Managed Switch
24
Configuration
Figure 6-3
Main Page of the Switch
6.2
Configure the Switch Using CLI
You can log in to the switch and access the CLI by the following two methods:
■
Log in to the switch by the Console (USB) port or Console (RJ-45) port on the switch.
■
Log in to the switch remotely by a Telnet or SSH connection through an Ethernet port.
■
Logon by a Console Port
The switch has two console ports: an RJ-45 console port and a Micro-USB console port. Console
output is active on devices connected to both console ports, but console input is only active on one
console port at a time. The Micro-USB connector takes precedence over the RJ-45 connector.
Install the TP-Link USB Console Driver if you are using the USB serial port for the first time on a
Windows-based PC. The driver can be found on the attached CD and Download page of our official
website. Refer to the User Guide to learn more about the installation.
To log in to the switch by the console port on the switch, please take the following steps:
1. Connect the PCs or Terminals to the console port on the switch by a provided cable. Refer to
5.3
Console Port
to learn how to connect.
2. If you attach a PC, start the terminal emulation program (such as the Hypertermi-nal) on the PC.
3. Specify the connection COM port in the terminal emulation program. If the Micro-USB console
port is used, you can view which COM port number is assigned to the USB serial port in the
following path:
Control Panel -> Hardware and Sournd -> Device Manager -> Ports -> USB Serial
Port.
4. Configure the terminal emulation program or the terminal. You can use the default settings as
follows:
■
Baud rate: 38400 bps