TP-Link TL-SG108PE Easy Smart SwitchUN User Guide - Page 81

Configuring PoE Auto Recovery

Get TP-Link TL-SG108PE PDF manuals and user guides View all TP-Link TL-SG108PE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Configuring PoE (Only for Certain Devices) Configuring PoE Auto Recovery 3 Configuring PoE Auto Recovery With PoE Auto Recovery enabled, the switch detects the link status between the ports and connected PDs. The switch pings the IP addresses of PDs constantly. If a PD loses connection, the switch will reboot it automatically. Choose the menu PoE > PoE Auto Recovery to load the following page. Follow these steps to enable PoE Auto Recovery and configure the parameters: 1) In the Global Config section, enable or disable PoE Auto Recovery. Click Apply. PoE Auto Recovery Enable or disable PoE Auto Recovery globally. Note: ●● Before upgrading the connected PoE powered device (PD), disable PoE Auto Recovery on the corresponding port to avoid PD's damage. ●● It is recommended to configure the switch and its connected PDs to the same subnet, and when 802.1Q VLAN enabled, the connected PD should be in the port's default VLAN (whose ID is the PVID). For detailed configurations, refer to Configuring 802.1Q VLAN. User Guide 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Configuring PoE (Only for Certain Devices)
Configuring PoE Auto Recovery
User Guide
77
3
Configuring PoE Auto Recovery
With PoE Auto Recovery enabled, the switch detects the link status between the ports
and connected PDs. The switch pings the IP addresses of PDs constantly. If a PD loses
connection, the switch will reboot it automatically.
Choose the menu
PoE > PoE Auto Recovery
to load the following page.
Follow these steps to enable PoE Auto Recovery and configure the parameters:
1) In the
Global Config
section, enable or disable PoE Auto Recovery. Click
Apply
.
PoE Auto Recovery
Enable or disable PoE Auto Recovery globally.
Note:
●
Before upgrading the connected PoE powered device (PD), disable PoE Auto Recovery on the
corresponding port to avoid PD’s damage.
●
It is recommended to configure the switch and its connected PDs to the same subnet, and
when 802.1Q VLAN enabled, the connected PD should be in the port’s default VLAN (whose ID
is the PVID). For detailed configurations, refer to
Configuring 802.1Q VLAN
.