TP-Link TL-SG108PE Easy Smart SwitchUN User Guide - Page 82

In the, select the desired ports and specify the parameters . Click, Ping IP Address - reset

Get TP-Link TL-SG108PE PDF manuals and user guides View all TP-Link TL-SG108PE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Configuring PoE (Only for Certain Devices) Configuring PoE Auto Recovery 2) In the Port Config section, select the desired ports and specify the parameters . Click Apply. Ping IP Address Enter the IP address of the PD connected to the port. Ping IP Address should be the same as the connected PD's IP address. Otherwise, the switch will continually reboot the PD. Startup Delay Specify how long the switch waits for the connected PD's rebooting before the switch starts to ping the PD's IP address. Interval Specify the interval between two consecutive ping packets. Failure Threshold Specify the threshold for ping failures. If the switch fails to get the ping response from the PD on the port, the switch will retry until the number of ping failures reaches the threshold, then the switch reboots the PD. Break Time Specify how soon the switch reboots the PD after the number of ping failures reaches the threshold. Failures Display the number of ping failures since the latest reboot of the PD. It will be reset when the PD responds to the ping packet or is rebooted. Reboots Display the number of PD's reboots. It will be reset after reaching 9,999 or when the switch is rebooted. Total Pings Display the total number of ping packets that the switch sends to the connected PD. It will be reset after reaching 9,999 or when the switch is rebooted. Status Enable or disable PoE Auto Recovery on the desired ports. To make it enabled, enable PoE Auto Recovery both globally and on the port. User Guide 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
User Guide
78
Configuring PoE (Only for Certain Devices)
Configuring PoE Auto Recovery
2) In the
Port Config
section, select the desired ports and specify the parameters . Click
Apply
.
Ping IP Address
Enter the IP address of the PD connected to the port.
Ping IP Address should be the same as the connected PD’s IP address.
Otherwise, the switch will continually reboot the PD.
Startup Delay
Specify how long the switch waits for the connected PD’s rebooting before the
switch starts to ping the PD’s IP address.
Interval
Specify the interval between two consecutive ping packets.
Failure Threshold
Specify the threshold for ping failures.
If the switch fails to get the ping response from the PD on the port, the switch
will retry until the number of ping failures reaches the threshold, then the switch
reboots the PD.
Break Time
Specify how soon the switch reboots the PD after the number of ping failures
reaches the threshold.
Failures
Display the number of ping failures since the latest reboot of the PD. It will be
reset when the PD responds to the ping packet or is rebooted.
Reboots
Display the number of PD’s reboots. It will be reset after reaching 9,999 or
when the switch is rebooted.
Total Pings
Display the total number of ping packets that the switch sends to the
connected PD. It will be reset after reaching 9,999 or when the switch is
rebooted.
Status
Enable or disable PoE Auto Recovery on the desired ports. To make it enabled,
enable PoE Auto Recovery both globally and on the port.