Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SG2216 » Manual Viewer

TP-Link TL-SG2216 TL-SG2424 v1 User Guide - Page 13

Rear Panel, Reset, 100/1000Mbps Ports, SFP Ports, Speed and Duplex, Switching, Port Config

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Figure 2-2 Front Panel of TL-SG2424 The following parts are located on the front panel of the Switch:  Reset: Press this button for five seconds or above to reset the software setting back to factory default setting.  10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding 1000Mbps LED and link/Act LED.  SFP Ports: Designed to install the SFP module. The SFP ports share the same LEDs with the corresponding RJ45 ports, and they are referred to as "combo" ports, which means they cannot be used simultaneously, otherwise only SFP ports work. Note: When using the SFP port with a 100Mbps module or a gigabit module, you need to configure its corresponding Speed and Duplex mode on Switching→Port→Port Config page. For 100M module, please select 100MFD while select 1000MFD for gigabit module. By default, the Speed and Duplex mode of SFP port is 1000MFD.  LEDs Name Power System 1000Mbps Link/Act Status On Flashing Off On Flashing Off On Off On Flashing Off Indication Power is on. Power supply is abnormal. Power is off or power supply is abnormal. The Switch is working abnormally. The Switch is working normally. The Switch is working abnormally. A 1000Mbps device is connected to the corresponding port. A 10/100Mbps device or no device is connected to the corresponding port. A device is connected to the corresponding port but no activity. Data is being transmitted or received. No device is connected to the corresponding port. 2.3.2 Rear Panel The rear panel of TL-SG2216/TL-SG2424 features a power socket and a Grounding Terminal (marked with ). 6

Section	Page
Package Contents	8
Chapter 1 About this Guide	9
1.1 Intended Readers	9
1.2 Conventions	9
1.3 Overview of This Guide	9
Chapter 2 Introduction	12
2.1 Overview of the Switch	12
2.2 Main Features	12
2.3 Appearance Description	12
2.3.1 Front Panel	12
2.3.2 Rear Panel	13
Chapter 3 Login to the Switch	15
3.1 Login	15
3.2 Configuration	15
Chapter 4 System	17
4.1 System Info	17
4.1.1 System Summary	17
4.1.2 Device Description	19
4.1.3 System Time	19
4.1.4 Daylight Saving Time	20
4.1.5 System IP	21
4.2 User Manage	22
4.2.1 User Table	22
4.2.2 User Config	23
4.3 System Tools	24
4.3.1 Config Restore	24
4.3.2 Config Backup	25
4.3.3 Firmware Upgrade	25
4.3.4 System Reboot	26
4.3.5 System Reset	26
4.4 Access Security	27
4.4.1 Access Control	27
Chapter 5 Switching	29
5.1 Port	29
5.1.1 Port Config	29
5.1.2 Port Mirror	30
5.1.3 Port Security	32
5.2 LAG	35
5.2.1 LAG Table	35
5.2.2 Static LAG	36
5.3 Traffic Monitor	37
5.3.1 Traffic Summary	37
5.3.2 Traffic Statistics	39
5.4 MAC Address	40
5.4.1 Address Table	41
5.4.2 Static Address	42
5.4.3 Dynamic Address	43
5.4.4 Filtering Address	45
Chapter 6 VLAN	47
6.1 802.1Q VLAN	48
6.1.1 VLAN Config	50
6.1.2 Port Config	52
6.2 Application Example for 802.1Q VLAN	54
Chapter 7 Spanning Tree	56
7.1 STP Config	61
7.1.1 STP Config	61
7.1.2 STP Summary	63
7.2 Port Config	63
7.3 MSTP Instance	65
7.3.1 Region Config	65
7.3.2 Instance Config	66
7.3.3 Instance Port Config	67
7.4 STP Security	69
7.4.1 Port Protect	69
7.4.2 TC Protect	72
7.5 Application Example for STP Function	72
Chapter 8 Multicast	76
8.1 IGMP Snooping	78
8.1.1 Snooping Config	79
8.1.2 Port Config	80
8.1.3 VLAN Config	81
8.1.4 Multicast VLAN	83
8.2 Multicast Filter	86
8.2.1 IP-Range	87
8.2.2 Port Filter	87
8.3 Packet Statistics	89
Chapter 9 QoS	91
9.1 DiffServ	94
9.1.1 Port Priority	94
9.1.2 Schedule Mode	95
9.1.3 802.1P Priority	96
9.1.4 DSCP Priority	96
9.2 Bandwidth Control	98
9.2.1 Rate Limit	98
9.2.2 Storm Control	99
Chapter 10 SNMP	101
10.1 SNMP Config	103
10.1.1 Global Config	103
10.1.2 SNMP View	104
10.1.3 SNMP Group	104
10.1.4 SNMP User	106
10.1.5 SNMP Community	107
10.2 Notification	110
10.3 RMON	111
10.3.1 History Control	112
10.3.2 Event Config	113
10.3.3 Alarm Config	113
Chapter 11 Maintenance	116
11.1 System Monitor	116
11.1.1 CPU Monitor	116
11.1.2 Memory Monitor	117
11.2 Log	117
11.2.1 Log Table	118
11.2.2 Local Log	119
11.2.3 Remote Log	119
11.2.4 Backup Log	120
11.3 Device Diagnose	121
11.3.1 Cable Test	121
11.3.2 Loopback	122
11.4 Network Diagnose	122
11.4.1 Ping	122
11.4.2 Tracert	123
Appendix A: Specifications	125
Appendix B: Configuring the PCs	126