TP-Link TL-WPA4226T KIT TL-WPA4220 V1 User Guide - Page 29

Wireless Advanced

Get TP-Link TL-WPA4226T KIT PDF manuals and user guides View all TP-Link TL-WPA4226T KIT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

TL-WPA4220/TL-WPA281 300Mbps AV500/AV200 WiFi Powerline Extender For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE is able to access the device, while all other wireless stations cannot access the device, you should configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field, enter Wireless Station A in the Description field and select Enabled in the Status pull-down list. Click the Save button. The filtering rules that configured should be similar to the following list:  Note: If you enable the function and select Deny the stations not specified by any enabled entries in the list to access for Filtering Rules but there isn't any enabled entry in the list, thus, no wireless stations can access the device. 3.4.4 Wireless Advanced Selecting Wireless > Wireless Advanced will allow you to do some advanced settings for the device in the following screen shown in Figure 3-16. As the configuration for each operation mode is almost the same, we take Access Point mode for example here. Figure 3-16 Wireless Advanced  Transmit Power - Specifies the transmit power of the device. You can select High, Middle or Low based on your need. High is the default setting and is recommended.  Beacon Interval - Specifies a value between 40-1000 milliseconds. The beacons are the packets sent by the device to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
For example:
If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE is able to
access the device, while all other wireless stations cannot access the device, you should configure the
Wireless MAC Address Filtering
list by following these steps:
1. Click the
Enable
button to enable this function.
2. Select the radio button:
Deny the stations not specified by any enabled entries in the list to
access
for
Filtering Rules.
3.
Delete all or disable all entries if there are any entries already.
4. Click the
Add New...
button and enter the MAC address 00-0A-EB-00-07-BE in the
MAC Address
field, enter Wireless Station A in the
Description
field and select
Enabled
in the
Status
pull-down
list. Click the
Save
button.
The filtering rules that configured should be similar to the following list:
Note:
If you enable the function and select
Deny the stations not specified by any enabled entries in the
list to access
for
Filtering Rules
but there isn’t any enabled entry in the list, thus, no wireless stations
can access the device.
3.4.4 Wireless Advanced
Selecting
Wireless
>
Wireless Advanced
will allow you to do some advanced settings for the device in
the following screen shown in Figure 3-16. As the configuration for each operation mode is almost the
same, we take Access Point mode for example here.
Figure 3-16 Wireless Advanced
Transmit Power -
Specifies the transmit power of the device. You can select
High
,
Middle
or
Low
based on your need.
High
is the default setting and is recommended.
Beacon Interval -
Specifies a value between 40-1000 milliseconds. The beacons are the packets
sent by the device to synchronize a wireless network. Beacon Interval value determines the time
interval of the beacons. The default value is 100.
21