Thermador CIT365GM Design Guide - Induction Cooktops - Page 4
Cooktops - Induction, Induction Cooktops - manual
View all Thermador CIT365GM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
COOKTOPS - INDUCTION INDUCTION COOKTOPS PLANNING INFORMATION MODEL OPTIONS There are two sizes of induction cooktops to choose from-30-inch and 36-inch. Models are available in our original black finish as well as our silver mirrored finish for those who want a bold, striking alternative that goes perfectly with stainless steel appliances. Be sure to reference the correct model information in this design guide. INSTALLATION CONSIDERATIONS The information in this design guide provides key features, product dimensions, cutouts and installation specifications. Before installing a Thermador Induction Cooktop, be sure to verify the cutout dimensions and electrical connections. Also, always consult with the installation manual packed with the product for complete details before installing. Thermador Induction Cooktops may be installed above a Thermador Single Built-in Oven. A minimum 1" air gap must be maintained between the bottom of the cooktop and the top of the oven. Thermador Cooktops may also be installed above a Thermador Warming Drawer to create a convenient cooking center. Refer to the warming drawer section for additional specifications. Solid surface countertops often require special installation. For example, heat reflective tape or rounded corners may be necessary. Contact the countertop manufacturer for instructions specific to your countertop. We strongly recommend the installation of a Thermador Ventilation System with this induction cooktop. Refer to the ventilation section for specifications. WARRANTY Limited warranty parts and labor (1 year) Limited warranty for glass ceramic surface/electronic elements and switches; Parts only (2nd to 5th year) See page 294 for additional warranty details. ELECTRICAL SPECIFICATIONS Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable local codes. All induction cooktops are dual rated, designed to be connected to either 240/208V AC, 60 Hz, 3 wire, single-phase power supply. Install a suitable conduit box (not furnished). An appropriately-sized, UL-listed conduit connector must be used to correctly attach the conduit to the junction box. MODEL CIT304GB CIT304GM CIT365GB CIT365GM CIS365GB REQUIRED CIRCUIT BREAKER 240V, 3 Wire, 60 Hz 208V, 3 Wire, 60 Hz 40 Amp 40 Amp 40 Amp 40 Amp 50 Amp 50 Amp 50 Amp 50 Amp 50 Amp 50 Amp Important: Local Codes may vary; installation, electrical connections and grounding must comply with all applicable local codes. If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit. ELECTRICAL LOCATION The junction box must be located within 3 feet (~900 mm) of the cooktop connection. It should be easily accessible for service purposes. 3 1/8" max (79 mm) + Fitting/Conduit 0.9" (23 mm) 12" approx. (300 mm) Connection ("J") box 1" min (26 mm) air clearance Conduit approx. 3 ft. ( 900 mm) CABINET REQUIREMENTS The distance from the top of the cooktop to the bottom of the cabinets above it must be A = 30" (762 mm) minimum. This distance can be reduced to A = 24" (610 mm) when the bottom of the wood or metal cabinet is protected by not less than 1/4" (6.35 mm) flame retardant millboard, covered by no. 28 steel sheet 0.015 (.4 mm) thick stainless steel, 0.024" (0.6 mm) aluminum, or 0.020" (0.5 mm) thick copper, at a minimum. Verify that the cabinets above the cooktop are a maximum of B = 13" (330 mm) deep. 1.800.735.4328 | THERMADOR.COM 103