Thermador KBUDT4865E Design Guide - Side-by-Side Refrigeration - Page 9

Custom Panel Series Side Panels

Get Thermador KBUDT4865E PDF manuals and user guides View all Thermador KBUDT4865E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

SIDE-BY-SIDE CUSTOM PANEL SERIES SIDE PANELS Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation. REFRIGERATOR AND SIDE TRIM DIMENSIONS The width and height of a side panel are determined by the type of installation you are planning. Notes: - The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions. - The side panel should be a minimum of 1/2" (1.27 cm) thick to avoid warping. - If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall. Refrigerator Overlay 23 59.40 cm) INSET INSTALLATION DIMENSIONS 1. Measure the distance from point A (as shown) to the back wall. Add 1/32" (0.8 mm) to this measurement to allow the side panel to fit into the trim. 2. If the panel is more than 3/8" (9.5 mm) thick, route the front edge to allow the side panel to fit into the trim. A RECESSED INSET INSTALLATION DIMENSIONS 1. Measure the distance from point A (as shown) to back wall. 2. Rout the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim. A Side Trim 9.7 mm) 4.5 mm) 1.5 mm) 3.2 mm) 268

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
268
Refrigerator
23
�⁄±
"
(59.40 cm)
Overlay
SIDE-BY-SIDE
CUSTOM PANEL SERIES SIDE PANELS
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an Inset or Recessed Inset panel installation.
REFRIGERATOR AND SIDE TRIM DIMENSIONS
The width and height of a side panel are determined by the type
of installation you are planning.
Notes:
–
The dimensions shown are actual product dimensions and may
not reflect the needed installation dimensions.
–
The side panel should be a minimum of
1
/
2
" (1.27 cm) thick to
avoid warping.
–
If the opening depth is 25" (63.5 cm) or more, you may want to
install a support board on rear wall.
INSET INSTALLATION DIMENSIONS
1.
Measure the distance from point A (as shown) to the back
wall. Add
1
/
32
" (0.8 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than
3
/
8
" (9.5 mm) thick, route the front
edge to allow the side panel to fit into the trim.
RECESSED INSET INSTALLATION DIMENSIONS
1. Measure the distance from point A (as shown) to back wall.
2.
Rout the front edge of the support board or attach a
3
/
8
"
(9.5 mm) board to hold the panel in the cabinet side trim.
Side Trim
�⁄²³
"
(4.5 mm)
�⁄±
"
(9.7 mm)
´⁄²³
"
(1.5 mm)
´⁄±
"
(3.2 mm)
A
A