Thermador PRD606WCG Installation Instructions - Page 23

Low backguard installation, optional

Get Thermador PRD606WCG PDF manuals and user guides View all Thermador PRD606WCG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Low backguard installation (optional) 2. Remove the drill point screws securing the piece to the back panel. Lift up to fully remove. 9 WARNING Fingers or hands could get pinched when installing the backguard. Severe injury could result. Use extreme caution and wear thick protective gloves to avoid potential laceration to finger or hand while sliding the backguard down onto the range. 9 WARNING To reduce the risk of fire or injury to persons, ensure all packaging has been removed from accessory devices before use. Installation methods will vary upon need. Before you begin read these instructions carefully. Observe all local codes and ordinances. To install the low backguard 1. Remove the T-20 torx stainless screws in the front face of the included island trim. 3. Align the back panel of the new accessory with the flanges on the range side panels right and left rear corners. Make sure the backguard front face is outside the flange on the front side of the range. 4. Reinstall screws removed in Steps 1 and 2. Page. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Page. 22
Low backguard installation
(optional)
9
WARNING
Fingers or hands could get pinched when installing
the backguard. Severe injury could result. Use
extreme caution and wear thick protective gloves to
avoid potential laceration to finger or hand while
sliding the backguard down onto the range.
9
WARNING
To reduce the risk of fire or injury to persons, ensure
all packaging has been removed from accessory
devices before use.
Installation methods will vary upon need. Before you
begin read these instructions carefully. Observe all local
codes and ordinances.
To install the low backguard
1.
Remove the T-20 torx stainless screws in the front face
of the included island trim.
2.
Remove the drill point screws securing the piece to
the back panel. Lift up to fully remove.
3.
Align the back panel of the new accessory with the
flanges on the range side panels right and left rear
corners. Make sure the backguard front face is outside
the flange on the front side of the range.
4.
Reinstall screws removed in Steps 1 and 2.