Thermador SGSX365FS Design Guide - Gas Cooktops - Page 10
Installation Options - sgs365fs cooktop
View all Thermador SGSX365FS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
COOKTOPS - gAS INSTALLATION OPTIONS INSTALLATION AbOve A WALL OveN Or WArmINg DrAWer Thermador Masterpiece® Gas Cooktops may be installed above a Thermador Single Built-in Oven as long as there is no contact between the bottom of the cooktop and the top of the oven. Thermador Masterpiece Gas Cooktops may also be installed above a Thermador Warming Drawer to create a convenient cooking center. Refer to the warming drawer section for additional specifications. ImPOrTANT We strongly recommend the installation of a Thermador Ventilation System with this gas cooktop. Seal the surfaces of the cutout to make them heat resistant. This prevents the surfaces from expanding as a result of humidity. Solid surface countertops require a special cutout size and special installation. For example, heat reflective tape or rounded corners may be necessary. Contact the countertop manufacturer for instructions specific to your countertop. NATurAL gAS Or LP Thermador Masterpiece Gas Cooktops are shipped by the factory to operate on natural gas. They must be converted for use with propane. Verify the type of gas being used at the installation site matches the type of gas used by the appliance. If the location/job site requires conversion from natural gas to propane (LP), order SNLPKITF. Field conversion must be done by qualified service personnel only. Please refer to the LP Conversion Instructions for further information. INSTALLATION ABOVE A THERMADOR BUILT-IN OVEN 5 11/16" (144 mm) 3 13/16" 4 3/16" (97 mm) (106 mm) COUNTERTOP 6 3/4" (172 mm) Gas Connection 36" (914 mm) COOKTOP SUMP 3/8" 11/8" (9 mm) (28 mm) OVEN 24 7/16" 281/4" (718mm) (621mm) 271/16" (687 mm) 3 "(76mm) 29 1/16" (738 mm) gAS COOKTOPS 36-INCh models: SgS365FS, SgSX365FS 36-INCH COOKTOP AND CUTOUT DIMENSIONS CABINET REQUIREMENTS Dimension requirements are for combustible surfaces. When the surface is protected by a material listed by UL as a Floor Protector and Wall Shield covered with not less than No. 28 MSG sheet metal 0.015 inch (0.38mm) stainless steel, 0.024 inch (0.6mm) aluminum or copper, it is considered noncombustible and some dimensions may be reduced. For a noncombustible surface over the cooktop, the minimum clearance is 24" (61cm) rather than 30" (76cm). Depth from Back Wall Cabinet 13" (33cm) max. Hood Depth - 24" (61cm) max. Above Counter - 30" (76 cm) min. to Combustible Surface SGS(X)30 - 30" (76cm) min. SGS(X)36 - 36" (91cm) min. 18" (46cm) min. Left Side 12" (30cm) min. Centered Over Cooktop Rear Wall - 1-3/4"(4cm) Right Side 12" (30cm) min. 43/4" (121mm) TOE KICK Note: Dimensions based on standard countertop height (36" with 43/4" toe kick including base plate). The built-in oven can be installed below the gas cooktop as long as there is no contact between the bottom of the cooktop and the top of the oven. WARNING: To reduce the risk of ignition of nearby combustible materials, install the countertop with a minimum distance of 12" (30cm) from side walls and 1 3/4" (4cm) from back wall.) NOTE: All measurements given have to be precisely followed. If nonstandard cabinets are used, make sure they are installed with minimum dimensions shown. Plan the installation of the unit so that the power cord, gas shut-off valve and gas pressure regulator are accessible from the front of cabinet. 1.800.735.4328 | THERMADOR.COM 119