Thermador T36BB110SS Product Specification Sheet - Page 3

Inch Built-in Bottom Freezer Refrigerator, Drawer, Pre-assembled

Get Thermador T36BB110SS PDF manuals and user guides View all Thermador T36BB110SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

PRELIMINARY PRELIMINARY T36BB110SS 3 6 - I N C H B U I LT- I N B O T T O M F R E E Z E R R E F R I G E R AT O R , 2 DRAWER, PRE-ASSEMBLED FREEDOM® COLLECTION, MASTERPIECE® SERIES HANDLES PROUD INSTALL CUTOUT DIMENSIONS Measurements in inches (mm) 351/2-36 (900-914) C ≥ 24 (≥ 610) 84 (2134) (B) (A) ≥ 4 (≥ 100) (C) ≤ 71/4 (≤ 185) C1 ≥ 4 (≥ 100) (C) C2 ≥ 4 (≥ 100) D (C) A: Socket B: Area for water and electric line routing C: Furniture return C1: Frameless cabinet C2: Framed cabinet D: Filler PLANNING NOTES Width: The minimum required cutout width is 35 1/2" (900 mm). Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install. Electrical Supply: The electrical supply outlet (A) is recommended to be located in an adjacent cabinet for safety and serviceability. If it is not possible due to the construction to connect the appliance to a power outlet next to it (A), connect the appliance to a power outlet behind the appliance (B). This alternative position of the power outlet is permissible only if you can switch off the outlet with a circuit breaker in the fuse box. Water Supply: The water supply is recommended to be located in an adjacent cabinet or other area that can be accessed after the appliance is installed. Furniture Return: The metal frame hides unfinished case returns for existing cabinetry that has not been custom built to accommodate the appliance. Ensure that the side walls of the cutout (C) are completely flush to a depth of at least 4" (102 mm). PROUD INSTALL TOP VIEW CLEARANCE Measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) 33/4 (95) 181/4 (463) ≥ 24 (≥ 610) PRELIMINARY PRELIMINARY 90° 115° 3815/16 (989) PLANNING NOTES Door Panels & Handles: Clearance dimensions are based on a door panel (A) thickness of ¾" (19mm). Additional clearances must be added for handles and door panels thicker than ¾" (19mm). Clearance Requirements: The required clearances for the maximum door opening angle of 115˚ should be followed. The minimum required clearance to fully access all compartments is 90˚ door opening. Page 3 of 4 9 / 23

  • 1
  • 2
  • 3
  • 4
Page 3 of 4
9 / 23
PROUD INSTALL TOP VIEW CLEARANCE
PROUD INSTALL CUTOUT DIMENSIONS
Measurements in inches (mm)
35
1
/
2
–36 (900–914)
1
/
8
–
3
/
8
(3–10)
≥
24
(
≥
610)
3
3
/
4
(95)
18
1
/
4
(463)
115°
38
15
/
16
(989)
90°
(
A
)
C
84
(2134)
≤ 7
1
/
4
(≤ 185)
(
B
)
≥ 4
(≥ 100)
(
C
)
≥ 4
(≥ 100)
(
C
)
C2
D
≥ 4
(≥ 100)
(
C
)
C1
≥ 24
(≥ 610)
35
1
/
2
–36
(900–914)
C1:
C2:
D:
C:
B:
A:
Furniture return
Frameless cabinet
Framed cabinet
Filler
Area for water and electric line routing
Socket
Measurements in inches (mm)
T36BB110SS
36-INCH BUILT-IN BOTTOM FREEZER REFRIGERATOR,
2 DRAWER, PRE-ASSEMBLED
FREEDOM
®
COLLECTION, MASTERPIECE
®
SERIES HANDLES
PLANNING NOTES
Width:
The minimum required cutout width is 35 1/2" (900 mm).
Depth:
The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install.
Electrical Supply:
The electrical supply outlet (A) is recommended to be located in an adjacent cabinet for safety and serviceability. If it is not possible
due to the construction to connect the appliance to a power outlet next to it (A), connect the appliance to a power outlet behind the appliance (B).
This alternative position of the power outlet is permissible only if you can switch off the outlet with a circuit breaker in the fuse box.
Water Supply:
The water supply is recommended to be located in an adjacent cabinet or other area that can be accessed after the appliance
is installed.
Furniture Return:
The metal frame hides unfinished case returns for existing cabinetry that has not been custom built to accommodate the appliance.
Ensure that the side walls of the cutout (C) are completely flush to a depth of at least 4" (102 mm).
PLANNING NOTES
Door Panels & Handles:
Clearance dimensions are based on a door panel (A) thickness of ¾” (19mm). Additional clearances must be added for
handles and door panels thicker than ¾” (19mm).
Clearance Requirements:
The required clearances for the maximum door opening angle of 115˚ should be followed. The minimum required clearance
to fully access all compartments is 90˚ door opening.
PRELIMINARY
PRELIMINARY
PRELIMINARY
PRELIMINARY