Toshiba 26C100U User Manual - Page 25

Setting channel skip

Get Toshiba 26C100U PDF manuals and user guides View all Toshiba 26C100U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 5: Setting up your TV Note: •• You must configure the ANT/CABLE input source before programming channels ( page 24). •• The automatic channel programming process will erase channels that were previously programmed into the TV's memory. •• To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. •• Programming channels when the ANT/ CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1無 Configure the antenna input source, if you have not already done so ( page 24). 2無 Press and open the Setup menu. 3無 Highlight Installation and press . The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message "Scanning channels, please wait" appears (as shown above). 5無 To cancel channel programming, press on the remote control (or highlight Cancel in the onscreen display and press ). When channel programming is finished, press or to view the programmed channels. Setting channel skip To prevent certain channels from being viewed, channel positions can be skipped. 1無 From the Setup menu, highlight Installation and press . 2無 Press p or q to select Channel Options and press . The list of channels will appear. 4無 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Program to bring up the Start Scan, and press again to begin channel programming. ANT/CABLE Antenna Scanning channels, please wait ... 52% Number of Channels Found - 73 Scanning Digital Channels Found Channel - 118 Abort 3無 Press p or q to select a channel position to be skipped and press . A tick will appear in the box.To remove the tick, press again. To add a channel to the channel memory: Highlight the checked box next to the channel number you want to add, and then press to remove the tick. To manually add digital subchannels on a physical channel: Use the Channel Numbers and the Dash ( ) on the remote control to enter the channel number (for example, 56-1). If the channel is found, the number will be added to the list and the box will be unchecked. If the channel is not found, a message will appear. Note: Skipped channels cannot be selected with or ; however, they can still be accessed using the number keys on the remote control. (continued) 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Chapter 5: Setting up your TV
25
Note:
•
You must configure the ANT/CABLE input source
before programming channels (
page 24).
•
The automatic channel programming process
will erase channels that were previously
programmed into the TV’s memory.
•
To tune the TV to a channel not programmed in
the channel memory, you must use the Channel
Number buttons on the remote control.
•
Programming channels when the ANT/
CABLE input is configured for
Cable
will take
substantially longer than when the antenna
input is configured for
Antenna
. This is
normal; however, once channel programming
is finished, you should not have to repeat the
programming process again unless your Cable
TV service lineup changes significantly.
To program channels automatically:
1無
Configure the antenna input source, if you have
not already done so (
page 24).
2無
Press
and open the
Setup
menu.
3無
Highlight
Installation
and press
.
4無
(A new set of
Installation
menu icons will appear,
as shown below.) Open the
Terrestrial
menu,
highlight
Channel Program
to bring up the
Start
Scan
, and press
again to begin channel
programming.
The TV will automatically cycle through all the
antenna channels, and store all active channels
in the channel memory. While the TV is cycling
through the channels, the message “Scanning
channels, please wait” appears (as shown above).
5無
To cancel channel programming, press
on
the remote control (or highlight
Cancel
in the on-
screen display and press
).
When channel programming is finished, press
or
to view the programmed channels.
Setting channel skip
To prevent certain channels from being viewed,
channel positions can be skipped.
1無
From the
Setup
menu, highlight
Installation
and
press
.
2無
Press
p
or
q
to select
Channel Options
and press
. The list of channels will appear.
3無
Press
p
or
q
to select a channel position to be
skipped and press
. A tick will appear in the
box.To remove the tick, press
again.
To add a channel to the channel memory:
Highlight the checked box next to the channel number
you want to add, and then press
to remove the tick.
To manually add digital subchannels on a
physical channel:
Use the Channel Numbers and the Dash (
) on
the remote control to enter the channel number (for
example, 56–1).
If the channel is found, the number will be added to
the list and the box will be unchecked.
If the channel is not found, a message will appear.
Note:
Skipped channels cannot be selected
with
or
; however, they can still be
accessed using the number keys on the remote
control.
(continued)