Toshiba 43H72 User Manual - Page 15

Programming for Use with a VCR or a Cable TV Converter, Cable converter - reset

Get Toshiba 43H72 PDF manuals and user guides View all Toshiba 43H72 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Introduction Connecting your TV Using the Remote Control To control a cable TV converter: Program the remote control to recognize the brand of your converter. The shaded buttons shown at right will control the cable TV converter. Set the TV/CABLE/VCR switch to the CABLE position. LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER RECALL POWER Programming the remote control for use with a VCR or a cable TV converter This remote control is pre-programmed to operate Toshiba VCRs. To use VCRs or cable converters other than Toshiba models, you must follow the steps below before you operate your remote control. 1. Refer to the "VCR code table" or "Cable TV converter code table" on pages 16-17 to find the number that corresponds to the brand name of your VCR or converter. If more than one number is listed, try each one separately until you find the one that works. 2. If you are reprogramming the remote control to operate your: • VCR, set the TV/CABLE/VCR switch on the remote control to VCR. • Cable converter, set the TV/CABLE/VCR switch on the remote control to CABLE. 3. While holding down the RECALL button, press the Number buttons (0-9) to enter the three-digit code of your brand of VCR or converter. 4. Point the remote control at the VCR or converter and press POWER to test the code. If the VCR or converter turns on, you have entered the correct code. If the VCR or converter does not respond to the remote control, you may have entered the wrong code. Repeat steps 1-4 with another code. 5. Reset the TV/CABLE/VCR switch to TV to control the TV. 123 CH 456 789 CH RTN VOL 100 0 ENT ADV/ PIP CH Channel yz Channel Number Enter FAVORITE EXIT PIC SIZE FAV MENU/ ENTER FAV STROBE ADV/ PIP CH STOP SOURCE PLAY PIP REC TV/VCR REW FF Note: • Each timeSTyILLouLOrCeATpElaSWcAeP the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch, it may not respond to any of the code numbers for your VCR brand name. In this case, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. For future reference, write down the code numbers you used: VCR code Cable code Setting up your TV Using the TV's Features Appendix Index 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Introduction
Connecting
y
our TV
Using the
Remote Control
Setting up
y
our TV
Using the TV’s
F
eatures
Appendix
Index
15
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
PIC SIZE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
STROBE
ENTER
To control a cable TV converter:
Program the remote control to recognize the brand of your
converter. The shaded buttons shown at right will control the
cable TV converter.
Set the TV/CABLE/VCR switch to the CABLE position.
Programming the remote control for use with a
VCR or a cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs. To
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
1.
Refer to the “VCR code table” or “Cable TV converter code
table” on pages 16-17 to find the number that corresponds to the
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
2.
If you are reprogramming the remote control to operate your:
•
VCR,
set the TV/CABLE/VCR switch on the remote control
to VCR.
•
Cable converter,
set the TV/CABLE/VCR switch on the
remote control to CABLE.
3.
While holding down the RECALL button, press the Number
buttons (0-9) to enter the three-digit code of your brand of VCR
or converter.
4.
Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR or converter turns on, you have entered the correct
code.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong code. Repeat steps 1-4 with
another code.
5.
Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code numbers you used:
VCR code
_____________________
Cable code
_____________________
Note:
•
Each time you replace the batteries, you
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled
“
VCR1/VCR2.
”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
POWER
Channel
yz
Channel
Number
Enter
RECALL