Toshiba HD-XA1 Owner's Manual - English - Page 16

Preparation of the remote control

Get Toshiba HD-XA1 - HD DVD Player PDF manuals and user guides
UPC - 022265412060
View all Toshiba HD-XA1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

1 Chapter Introduction Preparation of the remote control Set up the remote control to operate the player and your TV. Loading batteries Operating with the remote control 1 Open the cover. Point the remote control at the remote sensor and press the buttons. 2 Insert batteries. 7Use 4 batteries (AAA sizes). 7Make sure to match the + and - on the batteries to the marks inside the battery compartment. 3 Close the cover. Distance: About 7 m (23 ft) from the front of the remote sensor Angle : About 30° in each direction of the front of the remote sensor Notes Do not drop or give the remote control a shock. Do not leave the remote control near an extremely hot or humid place. Do not spill water or put anything wet on the remote control. Do not disassemble the remote control. Dispose of batteries in a designated disposal area. Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations. If the remote control does not operate correctly, or if the operating range becomes reduced, replace all batteries with new ones. When necessary to replace batteries in the remote control, always replace all batteries with new ones. Never mix battery types or use new and used batteries in combination. Be sure to use AAA size batteries. Always remove batteries from remote control if they are dead or if the remote control is not be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment. Caution Never throw batteries into a fire. About the remote control backlight The remote control has a backlight function for conveniently illuminating the buttons when you use the remote control in a dark room, etc. 7Lights for approximately 10 seconds when a button is pressed. 7Lights for approximately 10 seconds when the remote control senses a certain amount of vibration (approximately 1 second for a small amount of vibration). 16 To turn off the backlight function Press and hold for at least approximately three seconds. To turn back on the backlight function, press and hold again for at least approximately three seconds. Note The backlight function is on by default. Using the backlight function shortens the lifespan of the batteries.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
16
1
Chapter
1
Introduction
The remote control has a backlight function for
conveniently illuminating the buttons when you use the
remote control in a dark room, etc.
7
Lights for approximately 10 seconds when a button
is pressed.
7
Lights for approximately 10 seconds when the
remote control senses a certain amount of vibration
(approximately 1 second for a small amount of
vibration).
Notes
Do not drop or give the remote control a shock.
Do not leave the remote control near an extremely hot or humid place.
Do not spill water or put anything wet on the remote control.
Do not disassemble the remote control.
Dispose of batteries in a designated disposal area.
Batteries should always be disposed of with the environment in mind.
Always dispose of batteries in accordance with applicable laws and regulations.
If the remote control does not operate correctly, or if the operating range becomes reduced, replace all batteries with
new ones.
When necessary to replace batteries in the remote control, always replace all batteries with new ones. Never mix
battery types or use new and used batteries in combination.
Be sure to use AAA size batteries.
Always remove batteries from remote control if they are dead or if the remote control is not be used for an extended
period of time. This will prevent battery acid from leaking into the battery compartment.
Caution
Never throw batteries into a fire.
Point the remote control at the remote sensor and
press the buttons.
Distance
: About 7 m (23 ft) from
the front of the remote
sensor
Angle
: About 30° in each
direction of the front
of the remote sensor
Open the cover.
Insert batteries.
7
Use 4 batteries (AAA sizes).
7
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Close the cover.
1
2
3
Set up the remote control to operate the player and your TV.
Preparation of the remote control
Loading batteries
Operating with the remote control
About the remote control backlight
To turn off the backlight function
Press and hold
for at least
approximately three seconds.
To turn back on the backlight function, press and hold
again for at least approximately three seconds.
Note
The backlight function is on by default. Using the
backlight function shortens the lifespan of the batteries.