Toshiba MW26G71 Service Manual - Page 51

WHEN REPLACING EEPROM (MEMORY) IC INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 1F00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 1F10 5C 00 3B 03 59 00 05 02 A8 58 01 58 05 DF 02 E0 1F20 01 B1 03 69 00 03 00 00 61 FE 05 F5 00 00 08 3F 1F30 00 BF 07 00 00 00 C0 03 C0 03 00 00 EF 02 EF 02 1F40 E0 01 29 03 60 00 95 00 1C 00 1C 00 54 00 54 00 1F50 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 1F60 5C 00 3B 03 3E 00 05 02 A8 58 01 22 06 DF 02 E0 1F70 01 B1 03 69 00 03 00 00 61 FE 05 F5 00 00 08 3F 1F80 00 BF 07 00 00 00 C0 03 C0 03 00 00 EF 02 EF 02 1F90 E0 01 29 03 60 00 95 00 1C 00 1C 00 54 00 54 00 1FA0 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 1FB0 5C 00 3B 03 1D 00 05 02 A8 58 01 1C 07 DF 02 E0 1FC0 01 B1 03 69 00 03 00 00 61 FE 05 F5 00 00 08 3F 1FD0 00 BF 07 55 80 80 C0 03 C0 03 00 00 EF 02 EF 02 1FE0 E0 01 29 03 60 00 95 00 1C 00 1C 00 54 00 54 00 1FF0 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 2000 58 00 37 03 1D 00 05 02 A8 58 01 1C 07 DF 02 E0 2010 01 B1 03 69 00 03 01 43 82 FE 05 00 08 12 07 D7 2020 00 D5 05 77 80 80 DD 02 DD 02 00 00 EF 02 EF 02 2030 E0 01 29 03 7A 00 35 04 1C 00 1C 00 F3 03 F3 03 2040 01 Table 1-10 1. Turn on the POWER, and set to the TV mode. 2. Enter DATA SET mode by setting VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. 4. ADDRESS is now selected and should "blink". Using the UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 5. Press RIGHT/LEFT button to select DATA. When DATA is selected, it will "blink". 6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected. 7. Pressing RIGHT/LEFT button will take you back to ADDRESS for further selection if necessary. 8. Repeat steps 4 to 7 until all data has been checked. 9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 10. Turn on the POWER, and set to the TV mode. 11. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 12. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C4-10