Toshiba SD-V295KU Owners Manual - Page 52
Parental control setting, ENTER, Number buttons 0-9, ENTER., OPEN/CLOSE
View all Toshiba SD-V295KU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 52 highlights
Function setup (DVD) Customizing the function settings (Continued) Setting details PMENa.ieBgrne.hLunt.tMalode : OEnffglish STQVuSboStucitnrledSeent Passw: EO4o:nfr3fdglish OADuisgdtpiptiloaualtyOut : POIEnCnntegMrlilsahce Picture MDiovdXe(R) V: AOuDto JPEG Interval : 5 Seconds Screen Saver : On DMEPa.ReBrnCe.Lun.tal : OEnffglish QSTPVauSsboSstuciwtnrloedredn : EO4C:nhn3galnisghe ADOuisdtppilouaty : OIEnnntegrlilsahce PDicvtXu(rRe)MVOodDe : DAuistpolay JPEG Interval : 5 Seconds Screen Saver : On ■ Night Mode Night Mode enables you to control the dynamic range so as to achieve a suitable sound for your equipment. Off: It plays back at the recording level on the disc. On: Loud sound such as explosion is toned down slightly when played back. This is suitable when it is connected to a stereo. Notes: • This function works only when the disc recorded with Dolby Digital is played back. • The level of Night Mode may differ depending on DVD video disc. ■ QSound This DVD video player equipped with a "QSound". It can produce the effect of being in a cinema or a concert hall. Off: The QSound is disengaged. On: The QSound operates. Notes: • The QSound setting can also be changed with AUDIO on the remote control 40 . • This function works only when the disc recorded with Dolby Digital is played back. • When this function works, the volume might changed. • When the voice is distorted, turn off QSound. ■ Digital Out You can select the digital output sound format corresponding to your system connection. PCM: Change Dolby Digital to PCM for the output. Select when connected to a 2 channel digital stereo amplifier. Bitstream: Disc audio bitstream data will be output. Off: There is no sound output from DIGITAL AUDIO OUT jack. Note: Even if you select "Bitstream", MPEG Audio will be output in PCM format. 52 ■ Parental control setting Some discs are specified as not suitable for children. Such discs can be limited not to playback with the unit. 1) Press ▲ or ▼ to select "Parental", then press ENTER. "Enter Password" screen will appear. 2) Press "0000" using Number buttons (0-9). (Please note, this is pre-setting password of this unit). Then press ENTER. The parental level list will appear. • Level Off: The parental control setting does not function. • Level 8: Virtually all DVD software can be played back. • Level 1: DVD software for adults cannot be played back. 3) Press ▲ or ▼ to select from the level 1 to level 8. Then press ENTER. The limitation will be more severe as the level number is lower. 4) Press OPEN/CLOSE to activate Parental control setting. Notes: • The parental control level is equivalent to the following USA movie ratings. Level 1: G Level 2: Level 3: PG Level 4: PG-13 Level 5: Level 6: R Level 7: NC-17 Level 8: The parental control levels for other countries/area than U.S. are included for future use. Check the appropriate parental control level when you buy a DVD video disc equipped with the parental control feature in the future. • Depending on the discs, the unit cannot limit playback. • Some discs may not be encoded with specific rating level information though its disc jacket says "adult." For those discs, the age restriction will not work. • The password is required every time when you change the parental level. • If you input a wrong number, press CLEAR. 2K10101A.indb 52 12/22/2006 5:12:14 PM