Toshiba TDP-PX10U Mobile Projector TDP-PX10U Owner's Manual - Page 9

IMPORTANT PRECAUTIONS, Moisture Condensation, Place and Manner of Installation, Avoid Volatile Liquid

Get Toshiba TDP-PX10U - XGA DLP Projector PDF manuals and user guides
UPC - 032017964570
View all Toshiba TDP-PX10U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Before Using IMPORTANT PRECAUTIONS Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature to prevent the unit from possible damage. Place and Manner of Installation • Do not place in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the projector. • Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening their lives, and darkening the screen. • Do not use this product in the upright position or tilt it up or down by more than 20° from level. Doing so may cause a failure or shorten the life of the product. • Using this instrument near a TV or radio may cause interference to the images or audio sound. If this happens, move it away from the TV or radio. • Moving the projector from a low-temperature room to a high-temperature room may cause condensation on the lens or internal parts. If you continue to use it in that situation, it may malfunction. Wait until the condensation naturally disappears. • In a high altitude location such as over 600m (2000ft) from sea level, the air is thin and cooling efficiency is reduced so use the projector with [Fan mode] set to [High]. Otherwise, surface of the projector become hot and the lifetime may be reduced. p.36 • Only plug the power cord into outlets rated for use with the power cord's specified voltage range. Do not overload extension cords or power strips as this can result in fire or electric shock. • Route the power cable or the connecting cable away from where people could trip over it. The projector may fall, which could result in severe injury. • Be sure the power cord is easily reached for unplugging in case of emergency. Do not place any obstacles near a wall outlet in which the cord is plugged. Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time, as they will leave marks on the finish. Do not use a chemically saturated cloth. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
9
Before Using
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
•
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
•
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
•
Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
•
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
•
Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts. If you continue to use it in that
situation, it may malfunction. Wait until the condensation naturally disappears.
•
In a high altitude location such as over 600m (2000ft) from sea level, the air is thin and
cooling efficiency is reduced so use the projector with [
Fan mode
] set to [
High
].
Otherwise, surface of the projector become hot and the lifetime may be reduced.
•
Only plug the power cord into outlets rated for use with the power cord's specified
voltage range. Do not overload extension cords or power strips as this can result in fire
or electric shock.
•
Route the power cable or the connecting cable away from where people could trip over
it. The projector may fall, which could result in severe injury.
•
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time, as they will leave marks on the finish. Do
not use a chemically saturated cloth.
p.36