Toshiba TDP S20 Owners Manual - Page 11
Connection, Placement - replacement lamp
View all Toshiba TDP S20 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
Placement Placement Styles As shown in the figures below, this device can be placed in 4 different styles. The factory setting is "floor-mounted front projection." Set the Projection mode in the default setting menu p.32 , in accordance with your needs. Floor-mounted front projection Floor-mounted rear projection Ceiling-mounted front projection Ceiling-mounted rear projection WARNING • Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury. • If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident. • If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact. Projection Distance and Size Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment.) Screen As seen from above projection size (inches) - 1.516 a (min length) = 29.85 90° projection size (inches) - 1.264 a (max length) = 24.88 As seen from the side Lens center H 90° a a is the distance (m) between the lens and the screen, and corresponds to a range of 1.15 m to 10.00 m. H is the height from the image bottom to the center of the lens. 20 projection projection distance a (m) size (inches) min length (zooming max) max length (zooming min) 30 - 1.15 36 1.15 1.40 40 1.29 1.56 60 1.96 2.36 80 2.63 3.17 100 3.30 3.97 150 4.97 5.98 200 6.65 7.99 250 8.32 10.00 300 10.00 - height (H) (cm) 5.5 6.6 7.3 11.0 14.6 18.3 27.4 36.6 45.7 54.9 Connection Before connection • Read the owner's manual of the device you are connecting to the projector. • Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.45 , etc. • Turn off the power of both devices before connecting. • The figure below is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.) Audio amplifier, etc. Computer (for control) Video recorder, DVD player, etc. To audio input White (L)/Red (R) Audio cable (not supplied) To RS-232C terminal p.47 To audio output White (L)/Red (R) Control cable Video cable (not supplied) To S-Video output S-Video cable (not supplied) MONITOR AUDIO OUT CONTROL COMPUTER 2 IN ( Y/PB/PR ) AUDIO IN COMPUTER 1 IN ( Y/PB/PR ) S-VIDEO R L VIDEO RGB cable (not supplied) To RGB output Audio cable RGB cable (not supplied) (supplied with TDP-S21) Audio cable (not supplied) To audio output To audio output To audio output White (L)/ Red (R) AV cable (not supplied) To video output RGB cable (supplied) To RGB output VCR Monitor cable Mini D-sub 15P-BNC (not supplied) To Y/CB/CR output Green (Y)/Blue (CB)/Red (CR) Conversion adapter BNC-pin (not supplied) Computer Document camera Computer DVD video recorder, etc. Notes • COMPUTER terminals 1 and 2 function identically. • For TDP-S21, the document camera should be connected to COMPUTER terminal 2. • The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2. 21 Preparations