Toshiba TLP-S10U Mobile Projector TLP-S10U Users Guide - Page 13

Using handy features I Using auto setting (Auto setting) This function sets up the projector to the optimum state for each type of the input signal by using simple operations. Control panel 1 Press the AUTO SET button. FAN TEMP LAMP ON INPUT ON / STANDBY The Auto setting menu appears. 2 Press the AUTO SET button again. VOL. - ZOOM+ MENU VOL. + The menu item is automatically adjusted/set. For computer input, the icon will appear during KEYSTONE AUTO SET ZOOM- processing. Remote Control CALL KEYSTONE ON/ STANDBY AUTOSET MUTE FREEZE RESIZE CANCEL INPUT Note • Auto adjustment/setting may not be performed correctly for input signals other than those supported by the projector p.38 , p.39 . G Manual adjustment and setting The menu items vary depending on the input type, as shown in the table below. Use the buttons to adjust the items in the table below, then press the button when you are finished. The menu disappears. (The CANCEL button on the remote control also allows you to exit the menu mode.) Input Computer Y/PB/PR Video S-video Select Item Select Item Item Description Phase Frequency Adjust with to eliminate flicker. Adjust with to eliminate periodic patterns and flickering when many vertical lines appear on the screen. H-position V-position Clamp 1 Clamp 2 Move left Move right Move up Move down Adjusts the clamp pulse position with or . Adjusts the clamp pulse width with or . Phase Adjust with to eliminate flicker. Signal format [ : Enter to setting mode] [ : Select one of the following] [Apply: ] 480i(525i)@60Hz/480p(525p)@60Hz/ 576i(625i)@50Hz/576p(625p)@50Hz/ 720p(750p)@60Hz/720p(750p)@50Hz/ 1080i(1125i)@60Hz/1080i(1125i)@50Hz/ 1035i(1125i)@60Hz/1152i(1250i)@50Hz Video mode [ : Enter to setting mode] [ : Select one of the followings] [Apply: ] NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43 Note • Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction. 24 I Correcting the keystone distortion (Keystone) When the foot adjuster p.23 is used to change the projection angle, the picture will undergo keystone (trapezoidal) distortion. This projector is capable of correcting this keystone distortion. Before correction After correction Control panel FAN TEMP LAMP ON INPUT ON / STANDBY ZOOM+ VOL. - MENU VOL. + KEYSTONE AUTO SET ZOOM- Remote Control CALL KEYSTONE ON/ STANDBY AUTOSET MUTE FREEZE RESIZE CANCEL INPUT 1 Press the KEYSTONE button. The Keystone menu appears. 2 Use the buttons for keystone adjustment. On completing the adjustment, press the button to dismiss the menu (you can also use the CANCEL button on the remote control for menu dismissal). The trapezoidal distortion will be automatically corrected. During the processing, the icon is displayed. Item Keystone Description Shrink button of the screen Shrink top of the screen Notes • Depending on the amount of keystone adjustment and the content of images, some information may be lost, or the picture quality may suffer. • Keystone adjustment will not change the shape of the menus. I Zooming out the images This equipment is provided with the digital zoom (electric zoom: 100-80%). (Note that the display, if digitally zoomed out, may suffer from some degradation.) 1 Press the ZOOM - button. Each time the ZOOM - button is pressed, the image is reduced in size. Control panel FAN TEMP LAMP ON Remote Control RESIZE INPUT ON / STANDBY ZOOM+ CANCEL INPUT VOL. - MENU VOL. + ZOOM+ VOL.- MENU VOL.+ 2 Press the ZOOM + button to bring it back to the original size. Each time the ZOOM + button is pressed, the image size increases. (You cannot make it larger than the original size.) KEYSTONE AUTO SET ZOOM- ZOOM- Notes • Pressing either the ZOOMor ZOOM+ button would display the icon. • The adjustment value will automatically be saved. 25 Operations