Troy-Bilt Bronco Operation Manual - Page 14

Drive Pedal

Get Troy-Bilt Bronco PDF manuals and user guides View all Troy-Bilt Bronco manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Parking Brake To set the parking brake: Fully depress the brake pedal. Move the parking brake lever into the parking brake position. Release the brake pedal to allow the parking brake to engage. To release the parking brake: Depress the brake pedal and the parking brake lever will move out of the parking brake position on its own. The parking brake will then be released. Release the brake pedal. NOTE: The parking brake must be set if the operator leaves the seat with the engine running or the engine will automatically shut off. Drive Pedal The drive pedal is located on the right side of the tractor, along the running board. Depress the drive pedal forward and the tractor will move in the direction that the shift lever is engaged in. To cause the tractor to travel forward, while at a complete stop, move the shift lever into the Forward position. Gradually step on the drive pedal and the tractor will begin to move forward. To move in Reverse, follow the same procedure only move the shift lever into the reverse position. The ground speed is controlled with the drive pedal. The further forward that the pedal is pivoted, the faster the tractor will travel. The pedal will return to its original position when it's not depressed. Refer to the Operation section of this manual for detailed instructions regarding the drive pedal. IMPORTANT: Always set the parking brake when leaving the tractor unattended. Deck Lift Lever Found on your tractor's right fender, the deck lift lever is used to change the height of the cutting deck. To use, move the lever to the left, then place in the notch best suited for your application. PTO (Blade Engage) Lever Found on the tractor's right fender, the PTO (blade engage) lever is used to engage power to the cutting deck. To operate, move the lever all the way forward. Moving the lever all the way rearward into the PTO OFF position disengages power to the cutting deck. NOTE: The PTO (blade engage) lever must be in the disengaged (PTO OFF) position when starting the engine. 14 Section 4- Controls & Features

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Parking Brake
To set the parking brake:
Fully depress the brake pedal. Move
the parking brake lever into the parking brake position. Release
the brake pedal to allow the parking brake to engage.
To release the parking brake:
Depress the brake pedal and the
parking brake lever will move out of the parking brake position
on its own. The parking brake will then be released. Release the
brake pedal.
NOTE:
The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut off.
Drive Pedal
The drive pedal is located on the right side of the
tractor, along the running board. Depress the
drive pedal forward and the tractor will move in
the direction that the shift lever is engaged in.
To cause the tractor to travel forward, while at
a complete stop, move the shift lever into the
Forward position. Gradually step on the drive
pedal and the tractor will begin to move forward.
To move in Reverse, follow the same procedure
only move the shift lever into the reverse position.
The ground speed is controlled with the drive pedal. The further
forward that the pedal is pivoted, the faster the tractor will
travel. The pedal will return to its original position when it’s not
depressed.
Refer to the Operation section of this manual for
detailed instructions regarding the drive pedal.
IMPORTANT:
Always set the parking brake when leaving the
tractor unattended.
Deck Lift Lever
Found on your tractor’s right fender, the deck lift
lever is used to change the height of the cutting deck.
To use, move the lever to the left, then place in the
notch best suited for your application.
PTO
(Blade Engage)
Lever
Found on the tractor’s right fender, the PTO
(blade
engage)
lever is used to engage power to the cutting
deck. To operate, move the lever all the way forward.
Moving the lever all the way rearward into the PTO
OFF position disengages power to the cutting deck.
NOTE:
The PTO
(blade engage)
lever must be in the
disengaged (PTO OFF) position when starting the
engine.
14
S
ECTION
4— C
ONTROLS
& F
EATURES