Troy-Bilt TB2BV Operation Manual - Page 4
Specifications, Cleaning And Storage, Maintenance And Repair Instructions, Operating Instructions,
View all Troy-Bilt TB2BV manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
OPERATING INSTRUCTIONS OPERATING TIPS • Assure the unit is not directed at anybody or any loose debris before starting the unit. • Always hold the unit securely when operating. Keep a firm grip on the handle. • To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. • Operate power equipment only at reasonable hours- not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday. • To reduce noise levels, limit the number of pieces of equipment used at any one time. • To reduce noise levels, operate power blowers at the lowest possible speed to do the job. • Check your equipment before operation, especially the muffler, air intakes and air filters. • Use rakes and brooms to loosen debris before blowing. • In dusty conditions, slightly dampen surfaces when water is available. • Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away. • Clean up after using blowers and other equipment. Dispose of debris appropriately. OPERATING THE UNIT AS A BLOWER INCORRECT POSITION CORRECT POSITION WARNING: After starting the unit, always stand on the left side of the unit to operate it as shown in figure 14 to keep from blocking the air intake. Use the blower for trees, shrubs, flower beds and hard-to-clean areas. Also use the unit around buildings, walls, overhangs, fences and screens, and for other normal cleaning procedures. Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches and gardens. Fig. 14 Hold the blower with the right hand. Do not stand on the right side of the blower when operating the unit (Fig. 14). If you do, you will be blocking the air intake and this will affect the unit's performance. Instead, be sure to stand on the left side of the unit to maximize the unit's efficiency (Fig. 14). Sweep from side to side with the nozzle several inches above the ground or floor. Slowly advance the unit, keeping the accumulated pile of debris in front of you. Most dry blowing operations are better suited to low speeds, rather than high. High speed blowing is a better way to move heavier items like large debris or gravel. OPERATING THE UNIT AS A VACUUM WARNING: To avoid serious personal injury, never unzip the vacuum bag without stopping the unit first. WARNING: As a vacuum, the unit is designed to pick up dry material such as leaves, grass, small twigs and bits of paper. To avoid serious personal injury, do not attempt to vacuum wet debris and/or standing water as this may result in damage to the blower/ vacuum. To avoid severe damage to the impeller, do not vacuum metal, broken glass or similar items. Fig. 15 WARNING: Avoid situations that could catch the vacuum bag on fire. Do not operate near an open flame. Do not vacuum warm ash from fireplaces, barbecue pits, brush piles, etc. Do not vacuum discarded cigars or cigarettes unless the cinders are completely cool. Use the unit for vacuuming up light debris like leaves and paper. Be sure the vacuum bag is zipped closed before operating the unit. Fig. 16 Place the shoulder harness over your head and onto your shoulder. Hold the vacuum with both on hands on the handle (Fig. 15), tilting the suction tube slightly, and use a sweeping action to collect light debris (Fig. 16). The debris will flow into the vacuum bag. Things such as small leaves and small twigs will be mulched as they pass through the fan housing, allowing the vacuum bag to hold more debris. Emptying the Vacuum Bag When the bag is full, suction will noticeably decrease. Turn off the unit and allow the impeller to stop before you unzip the bag. 1. While wearing eye protection and a dust mask, unzip the vacuum bag and empty the contents into a garbage bag or container. 2. Turn the bag inside out after initial emptying and vigorously shake out dust and debris. 3. Zip close and reinstall the vacuum bag. NOTE: Empty the bag after each use to avoid deterioration and obstructing air flow, which will reduce the performance of the vacuum. MAINTENANCE AND REPAIR INSTRUCTIONS WARNING: To prevent serious injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start. MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures, take your unit to a Troy-Bilt or other qualified service dealer. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by a TroyBilt or other qualified service dealer. NOTE: Please read the California/EPA statement that came with the unit for a complete listing of terms and coverage for the emissions control devices, such as the spark arrestor, muffler, carburetor, etc. FREQUENCY MAINTENANCE REQUIRED Before starting the engine Fill the fuel tank with fresh fuel mixture Every 10 hours (every 5 hours in vacuum mode) Clean and re-oil the air filter Every 25 hours Check the spark plug condition and gap AIR FILTER MAINTENANCE WARNING: To avoid serious personal injury, always turn your trimmer off and allow it to cool before you clean or service it. Air Filter Cover SEE p. 3 p. 4 p. 4 Locking Tab WARNING: Wear gloves to prevent injury when handling unit. Cleaning the Air Filter Failure to maintain your air filter properly can result in poor performance or can cause permanent damage to your engine. 1. To open the air filter cover, push the locking tab on the right side of the cover inward and pull the air filter cover slightly out and to the left (Fig. 17). 2. Remove the air filter (Fig. 18). 3. Wash the filter in detergent and water. Rinse the filter thoroughly and allow it to dry. 4. Apply enough clean SAE 30 motor oil to lightly coat the filter. 5. Squeeze the filter to spread and remove excess oil. 6. Replace the filter (Fig. 18). NOTE: If the unit is operated without the air filter, you will VOID the warranty. 7. To reinstall the air filter cover, position the hooks on the left side of the air filter cover into the slots at the left side of the back plate (Fig. 18). 8. Swing the cover to the right and press closed so the air filter cover tab snaps into the slot on the back plate (Fig. 19). IDLE SPEED ADJUSTMENT Slots Fig. 17 Back Plate Fig. 18 Air Filter Cover Slot Air Filter Locking Tab WARNING: This unit will need to be running during idle speed adjustment. Wear protective clothing and observe all safety instructions to prevent serious personal injury. Also, DO NOT set unit on any surface except a clean, hard area while starting or performing any adjustments. Debris, such as gravel, sand, dust, grass, etc., could be thrown by the blower tube and damage property or cause serious injury to bystanders or operator. Fig. 19 Idle Adjustment Screw The idle speed of the engine is adjustable. An idle adjustment screw is between the air filter cover and the engine starter housing (Fig. 20). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments. If, after checking the fuel and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows: 1. Start the engine and let it run at a high idle for a minute to warm up. Refer to Starting/Stopping Instructions. Fig. 20 2. Release the throttle trigger and let the engine idle. If the engine stops, insert a small Phillips in between the air filter cover and the engine cover (Fig. 20). Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly. MAINTENANCE AND REPAIR INSTRUCTIONS Checking the fuel, cleaning the air filter, and adjusting the idle speed should solve most engine problems. If not and all of the following are true: • the engine will not idle • the engine hesitates or stalls on acceleration • there is a loss of engine power Have the carburetor adjusted by an authorized service dealer. REPLACING THE SPARK PLUG Use a replacement part number 753-06193. The correct spark gap is 0.025 in. (0.635 mm). 1. Stop the engine and allow it to cool. 2. Grasp the plug boot firmly and pull the cap from the spark plug. 3. Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise. 0.025 in. (0.635 mm) CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder. Fig. 21 4. Replace cracked, fouled or dirty spark plug. Set the spark gap at 0.025 in. (0.635 mm) using a feeler gauge (Fig. 21). 5. Install a correctly-gapped spark plug in the cylinder head. Turn the 5/8 in. socket clockwise until snug. If using a torque wrench, torque to: 110-120 in.•lb. (12.3-13.5 N•m) Do not over tighten. 6. Reinstall the spark plug boot. CLEANING AND STORAGE WARNING: To avoid serious personal injury, always turn your unit off and allow it to cool before you clean or do any maintenance on it. CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage the plastic housing or handle. Wipe off any moisture with a soft cloth. STORAGE • Never store a fueled unit where fumes may reach an open flame or spark. • Allow the engine to cool before storing. • Store the unit locked up to prevent unauthorized use or damage. • Store the unit in a dry, well-ventilated area. • Store the unit out of the reach of children. Long Term Storage 1. Remove the fuel cap, tip the unit and drain the fuel into an approved container. NOTE: Do not use fuel that has been stored for more than 30 days. Dispose of the old fuel/oil mix in accordance with federal, state and local regulations. 2. Start the engine and allow it to run until it stalls. This ensures that all fuel has been drained from the carburetor. 3. Allow the engine to cool. Remove the spark plug and put 5 drops of any high quality motor oil or 2-cycle oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug. NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the unit after storage. 4. Thoroughly clean the unit and inspect it for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage. OPTIONAL ACCESSORY ELECTRIC STARTER AND POWER START BIT™ FEATURES This unit is designed to be started with an optional electric starter or Power Start Bit™ that are sold separately. If choosing to start the unit using one of these features or have questions, please contact your local retailer or call 1-800-828-5500 in the U.S (1-800-668-1238 in Canada) for more information and purchasing. You may also go to www.troybilt.com or www.troybilt.ca. Electric Start Feature Fig. 22 TROUBLESHOOTING CAUSE THE ENGINE WILL NOT START The fuel tank is empty The primer bulb was not pressed enough The engine is flooded The fuel is old (over 30 days) and/or improperly mixed The spark plug is fouled SOLUTION Fill the fuel tank with properly mixed fuel Press the primer bulb fully and slowly 10 times Move the choke lever to Position 3, hold down the trigger and pull the starter rope Drain the fuel tank and add fresh, properly mixed fuel Clean, gap or replace the spark plug THE ENGINE WILL NOT IDLE The air filter is plugged The fuel is old (over 30 days) and/or improperly mixed Improper idle speed Clean or replace the air filter Drain the fuel tank and add fresh, properly mixed fuel Adjust according to the Idle Speed Adjustment section THE ENGINE WILL NOT ACCELERATE The fuel is old (over 30 days) and/or improperly mixed The air filter is plugged Drain the fuel tank and add fresh, properly mixed fuel Clean or replace the air filter THE ENGINE LACKS POWER OR STALLS The fuel is old (over 30 days) and/or improperly mixed The air filter is plugged The spark plug is fouled Drain the fuel tank and add fresh, properly mixed fuel Clean or replace the air filter Clean, gap or replace the spark plug NOTE: For repairs beyond the minor adjustments listed above, locate your nearest authorized service center by calling the Customer Support Department at 1-800-828-5500 (U.S.) or 1-800-668-1238 (Canada). SPECIFICATIONS* Engine Type Air-Cooled, 2-Cycle Displacement 27 cc Idle Speed RPM 3,200-4,400 rpm Operating RPM 7,000 - 8,000 rpm Blower Velocity up to 150 mph (240 kmh) Blower Air Output up to 450 cfm (12.7 cmm) Mulching Ratio up to 10:1 Spark Plug Gap 0.025 in. (0.635 mm) Lubrication Fuel/Oil Mixture Fuel/Oil Ratio 40:1 Fuel Tank Capacity 14 oz. (414 ml) Vacuum Bag Capacity 1 bushel (35 l) Approximate Weight (no fuel 12 lbs. (5.44 kg) * All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. 4