URC LT-3201-GR Owners Manual - Page 7

Switch Configuration Settings, Configuration Logic, SmartStart, Security 2 DSK

Get URC LT-3201-GR PDF manuals and user guides View all URC LT-3201-GR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

LT-3200 Switch Security 2 DSK The DSK can be found on the front of the switch (metal plate) and inside the box. Switch Configuration Settings There are a couple of ways to configure a switch. The first is via the switch itself, while the second is via the programming software. Parameter # Of Config # Button Presses 1 1 2 2 About Power On State Invert Switch Description Default power state the switch will revert to after power loss. Inverts the switch. 5 3 LED Indicator Color Sets the default color of the LED Bar. 6 4 LED Indicator Intensity Sets the intensity of the LED Bar. 7 5 LED Indicator Intensity (When Off) Intensity of the LED Bar when the switch is off. Configuration Logic To enter configuration mode, hold down the Config Button (A) for 10-15 seconds and the LED Bar (B) will light up yellow. A Once your parameter has been selected, the LED Bar (B) will blink yellow. Now press up or down on the paddle to adjust the parameter settings to your liking. Finally, once you've settled on a customization, it's time to save the configuration settings. Hold the Config Button (A) for 10 seconds and the LED Bar (B) will then blink to confirm the settings were saved. SmartStart B SmartStart enabled products can be added into a Z-Wave network by scanning the Z- Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
LT-3200 Switch
7
Switch Configuration Settings
Thereareacoupleofwaystoconfigureaswitch.Thefirstisviatheswitchitself,whilethesecondisviathe
programmingsoftware.
Configuration Logic
Toenterconfigurationmode,holddowntheCon±gButton(
A
) for 10-15 seconds and
theLEDBar(
B
) will light up
yellow
.
Onceyourparameterhasbeenselected,theLEDBar(
B
)willblink
yellow.
Nowpress
upordownonthepaddletoadjusttheparametersettingstoyourliking.
Finally,onceyou’vesettledonacustomization,it’stimetosavetheconfiguration
settings.HoldtheCon±gButton(
A
)for10secondsandtheLEDBar(
B
)willthenblink
toconfirmthesettingsweresaved.
SmartStart
SmartStartenabledproductscanbeaddedintoaZ-WavenetworkbyscanningtheZ-
WaveQRCodepresentontheproductwithacontrollerprovidingSmartStart
inclusion.NofurtheractionisrequiredandtheSmartStartproductwillbeadded
automaticallywithin10minutesofbeingswitchedoninthenetworkvicinity.
Security 2 DSK
The DSK can be found on the front of the switch (metal plate) and inside the box.
Parameter
#
# Of Config
Button Presses
About
Description
1
1
Power On State
Defaultpowerstatetheswitchwillreverttoafterpower
loss.
2
2
InvertSwitch
Invertstheswitch.
5
3
LEDIndicatorColor
SetsthedefaultcoloroftheLEDBar.
6
4
LEDIndicatorIntensity
SetstheintensityoftheLEDBar.
7
5
LEDIndicatorIntensity(WhenOff)
IntensityoftheLEDBarwhentheswitchisoff.
A
B