URC Vivido-Dimmers Master Neutral Dimmer Manual - Page 1
URC Vivido-Dimmers Manual
View all URC Vivido-Dimmers manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
R F M ASTE R DIM MER - VL-9540-MND-X FOR DIMMABLE LED/CFL/INCANDESCENT/MLV/ELV/HALOGEN/DIMMABLE FLUORESCENT INSTALLATION INSTRUCTIONS WARNING: • Turn OFF circuit breaker or remove fuse(s) and test that power is off before wiring. • Never wire any electrical device with power turned on. Wiring dimmer with power on may cause permanent damage to dimmer and void warranty. • If you are not sure about any part of these instructions, please contact a licensed electrician. IMPORTANT: RF Master dimmer will not work or will become damaged if wired incorrectly, and warranty will be voided. Refer to wiring instructions provided on reverse side. OPERATION INSTRUCTIONS • Press once to turn lights ON at previously selected level. • Press again to turn lights OFF. • When lights are OFF, press and hold for 2 seconds for full brightness. • When lights are ON, press and hold for 2 seconds until the blue LED blinks. After the preset delay, the lights will begin fading to OFF (up to 4 minutes). • Amber ON/OFF LED indicates that dimmer is turned on. Z-Wave Device Network Installation Instructions 1.This product may be added to a new or existing Z-Wave network. This Z-Wave device has a blue LED, which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network. 2.To include this device in a Z-Wave network, select the command on your Z Wave controller for inclusion (Install, Add Device, Add Node, Include Device, etc.). Then press the device ON/OFF switch one time to include it in the network. The LED will stop blinking. 3.To exclude this device from a Z-Wave network, select the command on your Z-Wave controller for exclusion (Uninstall, Remove Device, Remove Node, Exclude Device, etc.). Then press the device ON/OFF switch one time to exclude it from the network. The LED will start blinking. 4.This product works with other Z-Wave products from different vendors and product categories as part of the same network. 5.This product is a listening node and it will act as a repeater in the Z-Wave network. It will perform the repeater function with Z-Wave products and from other Z-Wave vendors. DIMMING LEVEL ADJUSTMENT For maximum compatibility with different loads types, VL-9540-MND-X allows the user to set the minimum level. Also to save on power consumption VL-9540-MND-X allows the user to set the maximum level. 1. After installing the dimmer and restoring power, press on/off button to turn on the light. 2. Press and hold on/off button for five seconds until the blue dimmer LEDs begin to cycle rapidly (NOTICE- after two seconds blue dimmer LEDs will start to flash indicating activation of the delay off feature. Continue holding the ON/OFF button for three additional seconds until the blue dimmer LEDs begin to cycle rapidly.) 3. Release the button. Dimmer will set the light to the previously saved minimum level (that may cause the light to flicker or turn off). During initial setup, the light will set to the factory minimum default. 4. Press either the dim or bright buttons to change the minimum level until the light output is acceptable. 5. Press ON/OFF button. Blue dimmer LEDs will start to cycle rapidly again and the dimmer light will go to previously saved maximum level. 6. Press either the dim or bright buttons to change the maximum level until the light output is acceptable. 7. Press ON/OFF button, LED will flash indicating completion of programming • NOTE - To restore the default min/max, repeat the steps above and adjust light levels to full min/max settings by pressing dim/bright buttons until the light output no longer changes. • NOTE - User could ignore setting max or min by pressing on/off button without changing the dimmer level. Rapid start feature This feature ensures that LED/CFL lights turn on when the dimmer preset level is low. With this setting enabled, the lights may momentarily be brighter than the preset level (less than one second) and then dim down to the preset level. Depending on the type of light used, this feature may not be needed. To enable/disable the feature, turn lights on. Press and hold the on/off button for 10 seconds until the blue dimmer LEDs flash for the third time, then release the button. CAUTION: 1. Use only with 120V AC 60 Hz. 2. Do not exceed maximum rating of the dimmer as indicated on the device. 3. Must be installed and used in accordance with electrical codes. 4. If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician for installation. 5. Use only #14 or #12 copper wire rated for at least 75°C with these devices. Do not use with Aluminum wire. NOTES: 1.The RF Master Dimmer is wired directly to the light fixture. 2.The RF Master Dimmer is not compatible with standard 3-way switches. 3.For Multi-location applications (3-Way or 4-Way) the RF Accessory Dimmer(s) is used along with one RF Master Dimmer. 4.The RF Accessory Dimmer communicates via RF signals to control the light from more than one location. 5.For multi-location control use RF Smart Dimmer Master direct wired to the light along with RF Accessory (VL-9540-MND-X). The RF Accessory does not require direct connection to the light (use Association function). 6.Do not exceed the maximum load indicated in the table below. Catalog # Loads INC/ ELV/ FLR/ Halogen/ MLV VL-9540-MND-X CFL/ LED Maximum Load 600W/VA 300W READ BEFORE INSTALLATION! Switch Identification White White ACCESSORY Disconnect Switch Green Red ACCESSORY ACCESSORY Green Black Black Master Control Troubleshooting Guide Symptom Possible Cause Accessory Solution No Function. All LEDs are OFF Erratic operation or flickering LEDs A) Light bulb(s) burned out B) Circuit breaker is off or tripped C) Disconnect switch on the dimmer is pulled out to the OFF position D) Improper wiring E) Defective dimmer A) Loose wiring connections B) Low dim setting A) Replace light bulb B) Turn on the circuit breaker C) Push in the disconnect switch on the dimmer D) Check and correct wiring E) Replace dimmer A) Check and correct wiring B) Set minimum brightness to a higher level Lights turns on after long delay A) Rapid start feature is disabled B) Low dim setting A) Enable rapid start feature B) Set minimum brightness to a higher level Functions normally using the dimmer push buttons but not from Z-Wave controller and one of the blue LEDs blinks ON and OFF about once per second Functions normally using the Master dimmer control but not from Z-Wave controller and no LEDs are blinking Functions normally both locally and from a Z-Wave controller but can't be controlled from a dimmer accessory switch (VL-9542-AND-X) or other Z-Wave device Dimmer is warm to touch after a period of time Dimmer is not included in Z-Wave network Problem with RF communication on dimmer The dimmer accessory or other Z-Wave device is not associated with the dimmer you wish to control This is normal Include dimmer in a Z-Wave network using a Z-Wave controller. Refer to Z-Wave controller user manual for details Replace dimmer Create an association between the dimmer accessory or other device and the dimmer. Refer to your Z-Wave controller user manual for details No action required