Uniden HOMEPATROL-2 Owner s Manual - Page 17

Homepatrol, Ii Operations - sentinel

Page 17 highlights

HOMEPATROL‐II OPERATIONS Start‐Up Wizard The first time you turn on your HomePatrol‐II, it will take you through a startup wizard to install the Sentinel software and set up basic scanning criteria. To run the startup wizard again, tap and hold Help. Running the Startup Wizard 1. Plug the provided USB cable into your computer and into HomePatrol‐II's USB jack. HomePatrol‐ II's screen turns white during PC connection. When connected to the PC, HomePatrol‐II installs like an additional drive. 2. Allow the installation to Autorun. If you don't see an Autorun prompt, open the drive and navigate to the setup.exe file in the Setup folder. Double click setup.exe to run that program. 3. Sentinel will ask you where you want to install the software. Once the software is installed, click Close when prompted. NOTE: Sentinel uses the internet to check for firmware and radio data updates. 4. After installing Sentinel, disconnect HomePatrol‐II from the PC. HomePatrol‐II restarts initialization. Selecting Channels to Monitor HomePatrol‐II operations revolve around the ability for you to listen to the transmissions you want to. There are many ways to fine‐tune the transmissions your HomePatrol‐II receives:  Change your location  Select service types  Change the Range  Select Favorites Lists to use  Avoid transmissions  Selecting Nationwide Systems While HomePatrol‐II selects channels, the Channel Selection screen appears. For the first 5 seconds, the screen shows the message "0 Channels Selected" with Cancel (activated) and Other Option (deactivated) in the Feature Navigation bar. After 5 seconds, the screen shows the number of channels selected, increasing as more channels are selected. When channel selection completes, Other Options is activated and Cancel changes to Listen. If you select Other Options at this point, you can choose to take any of the actions listed previously except Avoid transmissions. If your selection results in many channels, your HomePatrol‐II will warn you that it will take a long time to scan through all selections and recommend that you change your criteria to reduce the number of channels selected. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43

11
HOMEPATROL
II OPERATIONS
Start
Up Wizard
The first time you turn on your HomePatrol
II, it will take you through a startup wizard to install the
Sentinel software and set up basic scanning criteria. To run the startup wizard again, tap and hold
Help
.
Running the Startup Wizard
1.
Plug the provided USB cable into your computer and into HomePatrol
II’s USB jack. HomePatrol
II’s screen turns white during PC connection. When connected to the PC, HomePatrol
II installs
like an additional drive.
2.
Allow the installation to Autorun. If you don’t see an Autorun prompt, open the drive and
navigate to the
setup.exe
file in the Setup folder. Double click
setup.exe
to run that program.
3.
Sentinel will ask you where you want to install the software. Once the software is installed, click
Close when prompted.
NOTE: Sentinel uses the internet to check for firmware and radio data updates.
4.
After installing Sentinel, disconnect HomePatrol
II from the PC. HomePatrol
II restarts
initialization.
Selecting Channels to Monitor
HomePatrol
II operations revolve around the ability for you to listen to the transmissions you want to.
There are many ways to fine
tune the transmissions your HomePatrol
II receives:
Change your location
Select service types
Change the Range
Select Favorites Lists to use
Avoid transmissions
Selecting Nationwide Systems
While HomePatrol
II selects channels, the
Channel Selection
screen appears. For the first 5 seconds, the
screen shows the message “0 Channels Selected” with
Cancel
(activated) and
Other Option
(deactivated)
in the Feature Navigation bar. After 5 seconds, the screen shows the number of channels selected,
increasing as more channels are selected. When channel selection completes,
Other Options
is activated
and
Cancel
changes to
Listen
.
If you select
Other Options
at this point, you can choose to take any of the actions listed previously
except Avoid transmissions.
If your selection results in many channels, your HomePatrol
II will warn you that it will take a long time
to scan through all selections and recommend that you change your criteria to reduce the number of
channels selected.