Vaddio EasyTALK Audio Bundle System A EasyTalk Solutions Manual - Page 39

Warranty Information

Get Vaddio EasyTALK Audio Bundle System A PDF manuals and user guides View all Vaddio EasyTALK Audio Bundle System A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

EasyTalk USB Solutions The EasyUSB Mixer/Amp and EasyMic MicPOD devices can be upgraded in the field with the use of the Vaddio Loader software application. The processes for firmware updates are as follows: Step 1: If you are uncertain about updating or upgrading the equipment, please contact Vaddio Technical Support first. There is a possibility that any device can be turned into a brick, so give Tech Support a call first to get the dos and don'ts of updating. For EasyUSB Mixer/Amp: Set Dip Switch 8 on the back of the Mixer/Amp to high. Power cycle the Mixer/Amp. Connect to the RS-232 port on the Mixer/Amp. Launch the Vaddio Loader application on the PC and set the COM port to the associated PC connection. Select the Mixer/Amp in the drop down list at the top of the page. Select the load file from your local or network folders. Press the Start button on the loader. This will begin the firmware update transfer to the unit. A progress bar will indicate when the transfer is complete. Never interrupt a transfer, even if it looks like it isn't doing anything. Interrupting a transfer can brick the unit. For EasyMic MicPODs: The EasyMic MicPOD or Ceiling MicPOD is updated through the Mixer/Amp. Only one EasyMic can be connected to the Mixer Amp during the upgrade process. The Mixer/Amp must have DIP Switch 8 in the high position for the firmware update processes. The RS-232 and COM port selection on the PC as described above is duplicated for the EasyMic process. Select either the EasyMic (Table) or EasyMic (Ceiling) from the drop down list at the top of the page. Browse to the desired firmware image to update the EasyMic with. The files will end with an .ldr extension. Press the start button to begin the image transfer to the device. A progress bar will indicate status during the update process. Once complete, plug the second EasyMic MicPOD into the Mixer/Amp and repeat. Warranty Information (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details): Vaddio EasyUSB Solutions - Document Number 342-0449 Rev C Page 39 of 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
EasyTalk USB Solutions
Vaddio EasyUSB Solutions - Document Number 342-0449 Rev C
Page 39 of 48
The EasyUSB Mixer/Amp and EasyMic MicPOD devices can be upgraded in the field with the use of the Vaddio
Loader software application.
The processes for firmware updates are as follows:
Step 1:
If you are uncertain about updating or upgrading the equipment, please contact Vaddio Technical Support
first.
There is a possibility that any device can be turned into a brick, so give Tech Support a call first to get the
dos and don’ts of updating.
For EasyUSB Mixer/Amp:
Set Dip Switch 8 on the back of the Mixer/Amp to high.
Power cycle the Mixer/Amp.
Connect to the RS-232 port on the Mixer/Amp.
Launch the Vaddio Loader application on the PC and set the COM
port to the associated PC connection.
Select the Mixer/Amp in the drop down list at the top of the page.
Select
the load file from your local or network folders.
Press the Start button on the loader.
This will begin the firmware
update transfer to the unit.
A progress bar will indicate when the transfer is complete.
Never interrupt a transfer,
even if it looks like it isn’t doing anything. Interrupting a transfer can brick the unit.
For EasyMic MicPODs:
The EasyMic MicPOD or Ceiling MicPOD is updated through the Mixer/Amp.
Only one
EasyMic can be connected to the Mixer Amp during the upgrade process.
The Mixer/Amp must have DIP Switch
8 in the high position for the firmware update processes.
The RS-232 and COM port selection on the PC as
described above is duplicated for the EasyMic process.
Select either the EasyMic (Table) or EasyMic (Ceiling)
from the drop down list at the top of the page.
Browse to the desired firmware image to update the EasyMic with.
The files will end with an .ldr extension.
Press the start button to begin the image transfer to the device.
A progress
bar will indicate status during the update process.
Once complete, plug the second EasyMic MicPOD into the
Mixer/Amp and repeat.
Warranty Information
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):