ViewSonic CINE1000 User Guide - Page 35

Maintenance And Security

Get ViewSonic CINE1000 - DLP Home Theater Projector PDF manuals and user guides
UPC - 766907202212
View all ViewSonic CINE1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

MMaaiinntteennaannccee aanndd SSeeccuurriittyy MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: 1. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations. 2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life. Warning: 1. Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to do so could result in a severe burn. 2. It is recommended that you do not attempt to replace the lamp while the projector is installed on a ceiling. If you do attempt this, wear protective goggles to prevent glass from a ruptured lamp getting into your eyes. 1. Lift the screw cover (A). Remove the screw on the lamp compartment cover (B) and then lift the lamp compartment cover (C). 2. Remove the two screws from the lamp module (A) and then lift the module handle up (B). 3. Pull up firmly to remove the lamp module. 4. Reverse Steps 1 to 4 to install the new lamp module. Note: The lamp module should be oriented as shown here when replacing. ViewSonic Cine1000 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
S
S
e
e
c
c
u
u
r
r
i
i
t
t
y
y
ViewSonic
Cine1000
29
M
AINTENANCE AND
S
ECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
1.
The lamp contains a certain amount of mercury and should be disposed of according to local or-
dinance regulations.
2.
Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.
Warning:
1.
Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to
do so could result in a severe burn.
2.
It is recommended that you do not attempt to replace the lamp while the projector is installed on
a ceiling. If you do attempt this, wear protective goggles to prevent glass from a ruptured lamp get-
ting into your eyes.
1.
Lift the screw cover (
A).
Remove the screw on the lamp com-
partment cover (
B
) and then lift the
lamp compartment cover (
C
).
2.
Remove the two screws from the lamp
module (
A
) and then lift the module
handle up (
B
).
3.
Pull up firmly to remove the lamp
module.
4.
Reverse Steps 1 to 4 to install the new
lamp module.
Note:
The lamp module should be ori-
ented as shown here when replacing.