ViewSonic PA503W PA503S User Guide English - Page 49

Installing the dust filter, Obtaining the filter hour information, For first time installation

Get ViewSonic PA503W PDF manuals and user guides View all ViewSonic PA503W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. 3. Tighten the screw the secures the dust filter. 2 1 3 For first time installation: 4. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 5. Press Enter and the Filter Settings page is displayed. 6. Highlight Filter Mode and press / to select On. The filter timer starts counting. Set Filter Mode to On only when using the projector after the dust filer (optional accessory) is properly attached. Failing to do so will result in a shorter lamp life. Obtaining the filter hour information 1. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 2. Press Enter. The Filter Settings page is displayed. 3. You will see the Filter Hours information on the menu. Cleaning the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. Loosen the screw the secures the dust filter. 3. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away. 4. Re-install the dust filter. 2 1 Resetting the filter timer 5. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 6. Press Enter and the Filter Settings page is displayed. 7. Highlight Reset Filter Hours and press Enter. A warning message is displayed asking if you want to reset the filter timer. 8. Highlight Reset and press Enter. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
44
•
If your projector is ceiling-mounted or is not easily accessible, pay special attention to
your personal safety when replacing the dust filter.
Installing the dust filter
1.
Be sure to turn off the projector and
unplug it from power source.
2.
As the arrows shown to the right, fit
the filter by aligning and inserting it
into the projector slots.
3.
Tighten the screw the secures the
dust filter.
For first time installation:
4.
Open the OSD menu and go to the
ADVANCED
>
Filter Settings
menu
.
5.
Press
Enter
and the
Filter Settings
page is displayed.
6.
Highlight
Filter Mode
and press
/
to select
On
. The filter timer starts counting.
Set Filter Mode to On only when using the projector after the dust filer (optional accessory) is
properly attached. Failing to do so will result in a shorter lamp life.
Obtaining the filter hour information
1.
Open the OSD menu and go to the
ADVANCED
>
Filter Settings
menu
.
2.
Press
Enter
. The
Filter Settings
page is displayed.
3.
You will see the
Filter Hours
information on the menu.
Cleaning the dust filter
1.
Be sure to turn off the projector and unplug it from power source.
2.
Loosen the screw the secures the dust filter.
3.
Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.
4.
Re-install the dust filter.
Resetting the filter timer
5.
Open the OSD menu and go to the
ADVANCED
>
Filter Settings
menu
.
6.
Press
Enter
and the
Filter Settings
page is displayed.
7.
Highlight
Reset Filter Hours
and press
Enter
. A warning message is displayed
asking if you want to reset the filter timer.
8.
Highlight
Reset
and press
Enter
.
1
2
3
1
2