Home » ViewSonic Manuals » Projectors » ViewSonic PJ560D » Manual Viewer

ViewSonic PJ560D PJ260D User Guide - Page 11

Using the Product - manual

UPC - 766907287219

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Using the Product Control Panel LED 2 1 5 6 7 8 43 1 Lamp LED indicator Refer to "LED Indicator Messages". 2 Power LED indicator Refer to "LED Indicator Messages". Button Function 3 MENU Display or exit the on screen display menus. 4 Turn the projector on or off. 5 SOURCE Manually select an input source. 6 Keystone Correct the keystone distortion. 7 Four directional buttons Use four directional buttons to select items or make adjustments to your selection. 8 RESYNC Resynchronize the projector to the input signal from a computer. This function is available for computer mode only. ViewSonic 5 PJ260D

Section	Page
PJ260D_Contents_Eng.pdf	7
Projector Features	7
Notes on the AC Power Cord	7
Package Contents	8
Projector with Lens Cap	8
AC Power Cord	8
VGA Cable (D-SUB to D-SUB)	8
Remote Control (IR)	8
AAA size batteries for remote control	8
CD-Wizard	8
Quick Start Guide	8
Projector Carrying Case	8
Projector Overview	9
Using the Product	11
Control Panel	11
Connection Ports	12
Remote Control	13
Installing the Batteries	14
1. Open the battery cover in the direction shown.	14
2. Install batteries as indicated by the diagram inside the compartment.	14
3. Close the battery cover into position.	14
Remote Control Operation	15
Installation	16
Connecting the Projector	16
Powering On/Off the Projector	17
Powering On the Projector:	17
1. Remove the projector lens cap.	17
2. Complete the AC power cord and peripheral signal cable(s) connections.	17
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	17
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	17
Powering Off the Projector:	17
1. Press button to turn off the projector lamp. You will see a message \	17
2. Press button again to confirm.	17
3. Disconnect the AC power cord from the electrical outlet and the projector.	17
4. Do not turn on the projector immediately following a power off procedure.	17
Adjusting the Projector	18
Adjusting the Projector Height	18
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	18
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	18
Adjusting the Projector Zoom and Focus	18
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	18
2. Adjust the image by sliding the zoom ring.	18
Adjusting Projection Image Size	19
Menu Operation	20
1. Press the MENU button to open the OSD menu.	21
2. When OSD is displayed, use p / q to select any feature in the main menu.	21
3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.	21
4. Adjust the settings with t / u.	21
5. Press the MENU button, the screen will return to the main menu.	21
6. To exit OSD, press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.	21
Maintenance	24
Cleaning the Lens	24
Cleaning the Projector Housing	24
Replacing the Lamp	25
1. Turn off the projector.	26
2. Unplug the power cord.	26
3. Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can access the lamp cover.	26
4. Loosen the screw in the lamp cover and remove the cover.	26
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	26
6. Insert the new lamp module into the projector and tighten the screws.	26
7. Replace the lamp cover and tighten the screw.	26
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	26
9. Reset the lamp hour. Refer to the “Setting (Computer / Video Mode)” menu.	26
Specifications	27
Appendix	28
LED Indicator Messages	28
Compatibility Modes	29
Computer:	29
Video:	29
Troubleshooting	30
Start-up problems	30