ViewSonic PJD5351 PJD5152, PJD5352 User Guide (English) - Page 22

Operation, Starting up the projector - remote control

Get ViewSonic PJD5351 - DLP Projector PDF manuals and user guides
UPC - 766907341010
View all ViewSonic PJD5351 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector flashes blue after power has been applied. 2. Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp. 3. Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on. The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Rotate the focus ring to adjust the image clearness. • If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. • To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off. 4. If the projector is activated for the first time, select your OSD language following the onscreen instructions. 5. Switch all of the connected equipment on. Operation 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Operation
19
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the
POWER
indicator light
on the projector flashes blue
after power has been applied.
2.
Remove the lens cap. If it is closed, it could
become deformed due to the heat produced by
the projection lamp.
3.
Press
POWER
on the projector or remote
control to start the projector. The
POWER
indicator light
stays blue when the projector is
on.
The start up procedure takes about 30 seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
•
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
4.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
5.
Switch all of the connected equipment on.
I
I