ViewSonic PJD7836HDL PJD7828HDL User Guide English - Page 57

Installing the dust filter, Obtaining the filter hour information, Cleaning the dust filter

Get ViewSonic PJD7836HDL PDF manuals and user guides View all ViewSonic PJD7836HDL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Make sure it clicks into place. For first time installation: 3. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu/ 4. Press Enter and the Filter Settings page is displayed. 5. Highlight Filter Mode and press / to select On. The filter timer starts counting. Set Filter Mode to On only when using the projector after the dust filer (optional accessory) is properly attached. Failing to do so will result in a shorter lamp life. Obtaining the filter hour information 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu/ 2. Press Enter. The Filter Settings page is displayed. 3. You will see the Filter Hours information on the menu. Cleaning the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. Press the latches on the dust filter and remove the filter from the projector. 3. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away. 4. Re-install the dust filter. Resetting the filter timer 5. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu/ 6. Press Enter and the Filter Settings page is displayed. 7. Highlight Reset Filter Hours and press Enter. A warning message is displayed asking if you want to reset the filter timer. 8. Highlight Reset and press Enter. The lamp time will be reset to '0'. CAUTION Remember to set Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer. The timer will continue counting the next time you fit the filter back on and set Filter Mode to On. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
52
•
If your projector is ceiling-mounted or is not easily accessible, pay special attention to
your personal safety when replacing the dust filter.
Installing the dust filter
1.
Be sure to turn off the projector and unplug it
from power source.
2.
As the arrows shown to the right, fit the filter
by aligning and inserting it into the projector
slots. Make sure it clicks into place.
For first time installation:
3.
Open the OSD menu and go to the
SYSTEM SETTING: ADVANCED
>
Filter
Settings
menu
/
4.
Press
Enter
and the
Filter Settings
page is displayed.
5.
Highlight
Filter Mode
and press
/
to select
On
. The filter timer starts counting.
Set Filter Mode to On only when using the projector after the dust filer (optional accessory) is
properly attached. Failing to do so will result in a shorter lamp life.
Obtaining the filter hour information
1.
Open the OSD menu and go to the
SYSTEM SETTING: ADVANCED
>
Filter Settings
menu
/
2.
Press
Enter
. The
Filter Settings
page is displayed.
3.
You will see the
Filter Hours
information on the menu.
Cleaning the dust filter
1.
Be sure to turn off the projector and unplug it from power source.
2.
Press the latches on the dust filter and remove the filter from the projector.
3.
Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.
4.
Re-install the dust filter.
Resetting the filter timer
5.
Open the OSD menu and go to the
SYSTEM SETTING: ADVANCED
>
Filter Settings
menu
/
6.
Press
Enter
and the
Filter Settings
page is displayed.
7.
Highlight
Reset Filter Hours
and press
Enter
. A warning message is displayed
asking if you want to reset the filter timer.
8.
Highlight
Reset
and press
Enter
. The lamp time will be reset to '0'.
CAUTION
Remember to set Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter Settings
menu when using the projector with the dust filter removed. Setting Filter Mode to Off does
not reset the filter timer. The timer will continue counting the next time you fit the filter back on
and set Filter Mode to On.