Viking VCBB363RSS Grille Kit Instructions - Page 5

General Information, Grille Removal

Get Viking VCBB363RSS PDF manuals and user guides View all Viking VCBB363RSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

General Information • Most of the unit's weight is at the top. Extra care is needed when moving the unit to prevent tipping. • Do Not remove protective film until unit is in operating position. • All four leveling legs must contact the floor to support and stabilize the full weight. • Do not drop unit. • Remove exterior shipping materials prior to moving unit into home. • Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury. • To avoid personal injury, wear gloves when performing any installation procedure and wear eye protection when cutting metal straps. Moving Unit TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury. Unpacking unit 1. Remove top and bottom strap. 2. Remove top cap. 3. Cut carton rear approximately 1/4" (0.6 cm) to 1" (2.5 cm) from right corner with a utility knife extended 1/4" (0.6 cm). 4. Remove carton and exterior packaging. Save cardboard shipping material to protect floor surface when installing unit. Remove anti-tip board, kickplate and door trim pieces (DF models) from rear of unit. Remove shipping brackets from skid by removing 4 bolts (2 on each side) with a 1/2" deep-well socket wench and a pair of pliers. Note: Tilting unit is not required to remove shipping brackets. Slip appliance dolly between unit and skid. Only use dolly from the rear of the unit to remove unit from skid. After the unit is removed from the skid, a dolly can be used from either side or the back BUT NOT THE FRONT. Note: Use excess packaging to protect decorative trim; also, verify that leveling legs are up (0" adjustment). 8 Grille Removal 1 2a Place unit in front of cutout. 2b (Professional) Lift center grille louver up and pull out. 3 designer (Designer) Pull the center grille louver up at an angle and pull out. 4 Using an 8" magnetic nut driver, remove the two 1/4" screws. Remove grille assembly. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
9
General Information
8
• Most of the unit’s weight is at the top.
Extra care is needed when moving the unit
to prevent tipping.
• Do Not remove protective film until unit is
in operating position.
• All four leveling legs must contact the floor
to support and stabilize the full weight.
• Do not drop unit.
• Remove exterior shipping materials prior
to moving unit into home.
• Use two or more people to move and
install unit. Failure to follow this instruction
can result in back or other injury.
• To avoid personal injury, wear gloves when
performing any installation procedure and
wear eye protection when cutting metal
straps.
TIP OVER HAZARD
Appliance is top heavy and tips easily when
not completely installed. Keep doors closed
until appliance is completely installed and
secured per installation instructions. Use two
or more people to move and install
appliance. Failure to do so can result in
death or serious injury.
Unpacking unit
1. Remove top and bottom strap.
2. Remove top cap.
3. Cut carton rear approximately 1/4”
(0.6 cm) to 1” (2.5 cm) from right corner
with a utility knife extended 1/4” (0.6 cm).
4. Remove carton and exterior packaging.
Save cardboard shipping material to
protect floor surface when installing unit.
Remove anti-tip board, kickplate and door
trim pieces (DF models) from rear of unit.
Moving Unit
Remove shipping brackets from skid by removing
4 bolts (2 on each side) with a 1/2” deep-well
socket wench and a pair of pliers.
Note:
Tilting unit is not required to remove
shipping brackets.
Slip appliance dolly between unit and skid. Only
use dolly from the rear of the unit to remove unit
from skid. After the unit is removed from the
skid, a dolly can be used from either side or the
back BUT NOT THE FRONT.
Note:
Use excess packaging to protect
decorative trim; also, verify that leveling legs are
up (0” adjustment).
1
2a
Place unit in front of cutout.
(Professional) Lift center grille louver up
and pull out.
2b
designer
3
(Designer) Pull the center grille louver up
at an angle and pull out.
Using an 8” magnetic nut driver, remove
the two 1/4” screws.
4
Remove grille assembly.
Grille Removal