Vtech LS6425-3 User Manual (LS6425-3 User Manual) - Page 8

Battery charging

Get Vtech LS6425-3 PDF manuals and user guides
UPC - 735078018687
View all Vtech LS6425-3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Getting started Battery charging Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 10 hours of continuous charging. See the table on page 58 for battery operating times. If the screen is blank or displays Place in charger, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. When the battery is low, the handset displays Low battery along with a flashing icon. If you are on a call in low battery mode, the handset plays short beeps to alert you. The following table summarizes the battery charge indicators and actions to take. Battery indicators The screen is blank, or displays Place in charger and flashes. The screen displays Low battery and flashes. The screen displays HANDSET X. Battery status Battery has no or very little charge. The handset cannot be used. Battery has enough charge to be used for a short time. Battery is charged. Action Charge without interruption (about 30 minutes). Charge without interruption (about 30 minutes). To keep the battery charged, place it in the telephone base or charger when not in use. If you place the handset in the telephone base or charger without installing a battery, the screen displays No battery. After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time (see page 13). To skip setting the date and time, press OFF/CANCEL. SET DATE MM/DD/YY 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Getting started
4
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). If necessary, place the handset in the telephone base or charger
to charge the battery. For best performance, keep the handset in the telephone
base or charger when not in use. The battery is fully charged after 10 hours of
continuous charging. See the table on page 58 for battery operating times.
If the screen is blank or displays
Place in charger
, you need to charge the
handset without interruption for at least 30 minutes to give the handset enough
charge to use the telephone for a short time. When the battery is low, the
handset displays
Low battery
along with a flashing
icon. If you are on a call in
low battery mode, the handset plays short beeps to alert you.
The following table summarizes the battery charge indicators and actions to take.
Battery indicators
Battery status
Action
The screen is blank, or
displays
Place in charger
and
flashes.
Battery has no or
very little charge. The
handset cannot be used.
Charge without interruption
(about 30 minutes).
The screen displays
Low battery
and
flashes.
Battery has enough
charge to be used for a
short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X
.
Battery is charged.
To keep the battery charged,
place it in the telephone base
or charger when not in use.
If you place the handset in the telephone base or charger without installing a
battery, the screen displays
No battery
.
After you install your telephone or power returns following a power outage, the
handset will prompt you to set the date and time (see page 13). To skip setting
the date and time, press
OFF
/CANCEL
.
SET DATE
MM/DD/YY