Vtech VCS752 Quick Start Guide - Rev 1 - Page 1
Vtech VCS752 Manual
View all Vtech VCS752 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
ErisStation®TM SWIPirCeolnefsesreCncoenPfheorneenwciethSTywsoteWmireless Mics Quick Start Guide b u s i n e s s p h o n e s .v t e c h . c o m Introduction To Adapter Parts checklist This quick start guide provides you with the basic installation, setup, and operation instructions. A limited set of features are described in abbreviated form. Your VCS752 SIP Conference Phone with Two Wireless Mics 3 pVCaSc75k2aLgANe contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Yopoeurmataioynreinfsetrrutocttihoensusfoerr'tshims ainnnuoavlafotirvSeclooamtnsdplefeteatiunrset-arlilcahtioVnTeacnhd product. AC power cord The ErisStation SIP Conference Phone with Two Wireless Mics is designed for use in office settings. It consists of a base unit and two wireless mics, enabling clear conversation between 1 participants in different areas of a meeting room. The VCS752 also has Bluetooth and DECT connectivity. After pairing Bluetooth devices with the VCS752, you can use the conference phone Bluetooth headset to make and for a private caonnsvweersr actD(eiwolClnuit.plhaorywceaelllorlswc,aobprlleuugsse) a For large meeting rooms, you can extend the range of the VCS752 with up to three VTech VCS850 DECT expansion speakerphones. SIP Conference Phone with Two Wireless Mics Quick Start Guide b u s i n e s s p h o n e s .v t e c h . c o m 2 Model: VCS752 EtherneQtucicakbsltaert guide Adapter ErisStation Network switch Base unit or router Wireless mic ×2 For more information on using the VCS752 Bluetooth and DECT features, see the VCS752 User's Manual, available at businessphones.vtech.com. (x4) (x4) Battery ×2 (x4) Battery door ×2 L i-ion Polymer batteries. (x4) Power adapter Model: VCS752 Slots User's manual Quick start guide User's manual AC power cord Phone line cord Quick start guide DC cpononewctorecarblecable ETVHCESR75N4T CABLE Ethernet Adapter Connection box cable Introduction ErisStation® is a registered trademark of VTech Communications, Inc. Orbitlink Wireless TechnologyTM is a trademark of VTech Communications, Inc. Wall outlet • The ErisStation SIP Conference Phone with Two Wireless Mics requires a network TcooAdnapnteer ction to an IP PBX to operate. Install the wireless mic battEethreyrnet cable This quick start guide assumes that your network infrastructure is established and that your IP PBX phone serviVcCSe752hLAaN s been ordered and configured for your location. For more information 3 1. Plug the battery connector securely into the socket inside about installation options Salontds phone setup, see the VCS752 the battery compartment. Insert the battery (with the label User's Manual and the VCS752 Administrator and Provisioning AC power cTorHd IS SIDE UP facing up) into the battery compartment. Manual, available at businessphones.vtech.com. • The AC power cord is intended for a vertical or floor mount 2. Slide the battery door until it clicks into place. position. The prongs are not design1ed to hold the plug in placeAifdaitpter is plugged into a ceiling or cabinet outlet. 2 DC power cable To power the VCS752 using Po(wEit:h yellow plugs) Ethernet cable 1. Plug one end of the Ethernet cable into the Ethernet port on the bottom of the unit. Network switch or router To purchase any accessories or replacements, visit our website at businessphones.vtech.com or call 1-888-370-2006. Network switch or router Status indicators overview Status indicators on the base unit 1 2 3 Battery X2 Slots Ethernet cable Network switch or router 2. Plug the other end of the cable into your network router or switch. When the base unit is powered up, the status indicators turn green for about two seconds. • You can connect the VCS752 to both PoE and AC power. Ensure that you connect the cables in the order shown in the first diagram under "Connect base unit." Once connected, the unit will use PoE. If PoE fails, the unit will use AC powerBaasttearybXac2kup. 3. Place the wireless mics into the charging cradles until they are flush. ErisStation The status indicator on the wireless mic turns orange when charging, and turns off when the wireless mic is fully charged. LED 1 Power up On a call Incoming call • Green for about two seconds. • Green during a call. • Red when a call is muted. • Flashes green when there is an incoming call. LED 2 (CELL 1) and 3 (CELL 2/HEADSET) (Blue) Bluetooth device connected • Steady Incoming call on Bluetooth device • Flashing Held call on Bluetooth device • Slow flashing Base is in discoverable mode • Alternating CELL 1/CELL 2 Connect base unit The VCS752 can be powered by AC power or Power over Ethernet (PoE-Class 0). When using AC power, connect the base unit as shown below. Wall outlet To Adapter Slots VCS752 LAN 3 AC power cord 1 DC power cable (with yellow plugs) Adapter 2 Ethernet cable Network switch or router 1. Plug one end of the DC power cable into the power jack of the base unit, and plug the other end into the VCS752 jack of the power adapter. Route the cord through the slots. 2. Plug one end of the Ethernet Slots cable into the LAN jack of the power adapter, and plug the other end into a network switch or router. 3. Plug the small end of the AC power cord into the power jack of the adapter, and plug the large end Network or router siwnitctho a wall outlet not controlled by a switchE.thernet cable • Power Line The supplied power adapter is designed for use with only the ErisStation SIP Conference Phone with Two Wireless Mics. It is not designed to power other network devices. Do not connect the supplied power adapter to any other network devices through the supplied DC power cable or any other Cat5e ethernet cable. Battery X2 Status indicator on the wireless mic Power up • Orange for about two seconds. On the cradle • Orange when charging in the cradle except during registration. • Flash red and green alternately when the non-registered wireless mic is charging on the cradle. Off the cradle • Green during a call. • Red when the system is muted during a call. • Off when the wireless mic is in idle mode or without a battery. • Flashes orange when the wireless mic's battery is low. • Flashes green when there is an incoming call. • Flashes red slowly when the wireless mic is: • out of range; or • not registered; or • off cradle during paging (with a paging tone). During registration • Flashes red and green alternately.