Waring FP25 Instruction Manual - Page 6

DISASSEMBLY of BATCH BOWL PARTS FP25 & FP25C ALWAYS UNPLUG THE CORD BEFORE DISASSEMBLING. • Turn the bowl cover clockwise until the safety interlock tab on the cover is disengaged from the magnetic safety interlock switch in the tower, and the tabs are clear of the groove in the tower. The bowl handle will be at a position between 7 o'clock and 9 o'clock. In this position you can lift the cover off the bowl. • Remove the large food pusher from the feed tube. Remove the small pusher from the large pusher. Disassembly when Removing the S-Blade • Remove the work bowl from the unit by rotating clockwise (left) to disengage the tabs on the bottom of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o'clock), you can gently lift the bowl straight up and out. It is recommended that you remove the bowl from the motor base before you remove the S-Blade. • To remove the blade, keep a slight downward pressure on the top of the center hub of the blade while removing the bowl from the motor base. This will form a seal to prevent food particles from spilling into the center tube of the bowl, and onto the motor base or the work surface. Then remove the S-Blade from the bowl. Handle the S-Blade with caution; the blades are extremely sharp. Disassembly when Removing an Accessory Disc • Do not remove the work bowl until the accessory disc is removed. • To remove an accessory disc, insert your thumb and forefinger into the 2 finger holes in the surface of the disc. • Remove the work bowl from the unit by rotating clockwise (left) to disengage the tabs on the bottom of the bowl platform from the work bowl. When the bowl handle is on the left (about 7 o'clock), you can gently lift the bowl straight up and out. 10 ASSEMBLY of CONTINUOUS FEED CHUTE PARTS FP25C • Clean and sanitize the motor base, and wash, rinse, and sanitize the continuous feed chute, cover, slinger disc, food pusher, food pusher insert and processing tools prior to initial use. • Place the base on a counter or table near a 3-prong electrical outlet. Position it so that you are looking at the front of the unit and can see the control levers. Be certain that the cord is unplugged and the OFF lever has been pressed. Do not plug in the cord until the processor is completely assembled. • Pick up the gray continuous feed chute, holding it in both hands with the chute pointing in the 4-o'clock position. Place the chute on the base, fitting its center opening over the motor shaft. Align the bowl locking slots on the bottom of the chute to the left of the gray locking tabs on the side of the bowl platform (motor base). • Press the chute down so the round lower rim of the chute fits around the circular platform. • Place the Slinger (or ejector disc) in the bowl, sliding it over the metal motor shaft until it reaches the bottom of the chute. • Select the appropriate UL listed accessory disc: Grating disc, shredding disc, slicing disc, waved slicing disc, pulping disc, or julienne/French fry disc. • Each of these discs has a disc stem. The disc stem fits over the double flat in the food processor's stainless steel motor shaft. The stem will fit inside either the clear plastic tube inside the bowl, or the continuous feed chute and slinger. • After selecting the appropriate disc, pick up the disc, either using the finger holes on the disc surface, or holding the disc firmly between both hands. Be careful not to grab the blades or scrape your hands on the shredding/grating nodules. • Carefully guide the disc stem over the metal shaft so the double flats on the shaft line up with the matching shape of the disc stem. It should easily drop into place, but if not, gently rotate until you feel the disc drop into place. Be sure it is pushed down as far as it will go. Push on the outside rim only; never touch the cutting blades. Do not put any food in the chute before placing the accessory disc onto the shaft. • Place the cover on top of the chute. Press down the cover until it is fully seated on all sides. Rotate the cover lock mechanism until it latches to the tab on the continuous feed chute. This will prevent the lid from rising up during processing. • Turn the chute and cover together, counterclockwise, until the discharge chute is in the 3-o'clock position and the locking tabs on the motor base are engaged in the bowl locking slots on the bowl bottom. • The interlock tab on the cover will simultaneously slide into the tower safety interlock slot and engage the magnetic safety interlock switch. The interlock switch prevents operation of the machine unless the cover is in the proper position. With this switch engaged, the food processor will operate, if the power is on and the controls are turned to ON or PULSE. NEVER ATTEMPT TO START THE FOOD PROCESSOR WITHOUT THE CHUTE AND COVER LOCKED INTO POSITION. 11