Weber Ducane SS 3-burner NG Owner Manual - Page 18

Troubleshooting

Get Weber Ducane SS 3-burner NG PDF manuals and user guides View all Weber Ducane SS 3-burner NG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

TROUBLESHOOTING PROBLEM IGNITION SYSTEM CHECK and CURE Be sure that there is gas flow to the burners by attempting to match light your burners. If match lighting is successful, the problem lies somewhere in the ignition system and will need to be checked. IMPORTANT MAIN GRILLING BURNERS ƽ CAUTION: Always turn the gas supply off at the main gas cut off before proceeding with any troubleshooting procedures. If, for any reason, the snap ignition fails to ignite the main grilling burner(s), repeat the lighting procedures described on the grill control panel. If the main burner(s) still fails to ignite, make sure that there is gas flowing to the burner(s) by attempting to match light the burner(s). If the burners will match light, then proceed with the ignition checkout. If for any reason the igniter system is still inoperative, follow match lighting instructions. ƽ WARNING: The hood must be in the full open position any time you attempt to light your grill. Failure to open the hood could lead to delayed ignition resulting in bodily harm. ROTISSERIE BURNER ELECTRONIC IGNITION After shutting off the main gas supply, remove the cook grate and heat distribution plates. Turn snap igniter counter clockwise and check if the electrode is sparking to the igniter tube. Try the snap igniter several times. With a fresh battery installed, push electronic ignition button and check if there is a spark between the two electrode tips. There needs to be a 1/8" to 3/16" gap between the electrode tips. If the gap is lesser or greater, carefully bend the electrode tips until you have the correct gap of 1/8" to 3/16"(A). Verify that the battery is in good condition and installed correctly. If so, try a new battery. If for any reason the igniter system is still inoperative, follow match lighting instructions. BURNERS WITH POOR FLAME Check to be sure burner ports, shutter, end of the burner (venturi) and orifice(s) are free of any obstructions. Also, if your grill has been stored over a prolonged period of time, check to make sure no spiderwebs have been formed in the shutter end of the burner (venturi) or over orifices. If you still have a poor flame, please contact dealer for futher assistance or call Customer Service If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.ducane.com. A 18 www.ducane.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
18
www.ducane.com
TROUBLESHOOTING
TROUBLESHOOTING
A
PROBLEM
CHECK and CURE
IMPORTANT
IGNITION SYSTEM
Be sure that there is gas flow to the burners by attempting to match light your burners.
If match lighting is successful, the problem lies somewhere in the ignition system and
will need to be checked.
MAIN GRILLING BURNERS
±
CAUTION: Always turn the gas supply off at the main gas
cut off before proceeding with any troubleshooting proce-
dures.
If, for any reason, the snap ignition fails to ignite the main grilling burner(s), repeat the
lighting procedures described on the grill control panel.
±
WARNING: The hood must be in the full open position any
time you attempt to light your grill. Failure to
open the
hood could lead to delayed ignition resulting in bodily
harm.
After shutting off the main gas supply, remove the cook grate and heat distribution
plates. Turn snap igniter counter clockwise and check if the electrode is sparking to the
igniter tube. Try the snap igniter several times.
If the main burner(s) still fails to ignite, make
sure that there is gas flowing to the burner(s)
by attempting to match light the burner(s).
If the burners will match light, then proceed
with the ignition checkout.
If for any reason the igniter system is still
inoperative, follow match lighting instructions.
ROTISSERIE BURNER ELECTRONIC
IGNITION
With a fresh battery installed, push electronic ignition button and check if there is a
spark between the two electrode tips. There needs to be a 1/8” to 3/16” gap between
the electrode tips. If the gap is lesser or greater, carefully bend the electrode tips until
you have the correct gap of 1/8” to 3/16”
(A)
.
Verify that the battery is in good condition
and installed correctly. If so, try a new battery.
If for any reason the igniter system is still
inoperative, follow match lighting instructions.
BURNERS WITH POOR FLAME
Check to be sure burner ports, shutter, end of the burner (venturi) and orifice(s) are
free of any obstructions. Also, if your grill has been stored over a prolonged period of
time, check to make sure no spiderwebs have been formed in the shutter end of the
burner (venturi) or over orifices.
If you still have a poor flame, please contact
dealer for futher assistance or call Customer
Service
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.ducane.com.