Weslo 720 Instruction Manual - Page 5

MAINTENANCE AND TROUBLE-SHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department. PROBLEM: THE POWER DOES NOT TURN ON SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) If an extension cord is needed, use only a 14-gauge cord of 1,5 m or less in length. Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. PROBLEM: THE POWER TURNS OFF DURING USE c Tripped Tripped Reset Reset SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key fully into the console. d. If the treadmill still will not run, please call our Customer Service Department. PROBLEM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 5 on page 6. Most problems are the result of drained batteries. b. First remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood. Carefully remove the hood. Locate the Reed Switch (8) and the Magnet (14) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm. If necessary, loosen the Reed Switch Screw (77) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. Top View 77 8 1/8" 17 14 ASSEMBLY Before beginning assembly, carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • As you assemble the treadmill, be sure that all parts are oriented as shown in the drawings. • Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, nonabrasive cleaner. The following tools (not included) are required for assembly: • Two (2) adjustable spanners • One (1) phillips screwdriver If further assistance is needed, please call our Customer Service Department at 0345-089009. 1. Refer to drawing 2 below. Note that the Console 1 (49) is connected to the right Upright (37) by the Wire Harness (53). During assembly steps 1-3, be careful to avoid damaging the Wire Harness. With the help of a second person, carefully lay the treadmill on its side. Position one of the Base Legs 37 (55) on the base of the Uprights (37) as shown. Make sure that the Base Leg Pads (31) and the Wheel (34) are in the indicated positions. Attach the Base Leg with two of the four Base Leg Bolts (28), Base Leg Washers (68), and Base Leg Nuts (61). Carefully turn the treadmill onto its other side. Assemble the other Base Leg (55) as described. With the help of a second person, carefully raise the treadmill to the upright position so the Base Legs (55) are resting flat on the floor. 2. Hold the treadmill firmly with both hands, and lower 2 the treadmill to the floor. To decrease the possibili- ty of injury, bend your legs and keep your back straight. 34 61 28 68 31 55 49 53 37 12 5