Weslo Cadence Ls 8 English Manual - Page 5

Assembly - seconds

Get Weslo Cadence Ls 8 PDF manuals and user guides View all Weslo Cadence Ls 8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

ASSEMBLY Assembly requires two people. Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. The following tools (not included) are required for assembly: two (2) adjustable wrenches and a phillips screwdriver . Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. 1. Note that the Right Handrail and the Console Base (not shown) are connected to the treadmill by a Wire Harness. During assembly steps 1 through 3, be careful not to pull on or damage the Wire Harness. With the help of a second person, carefully lay the treadmill on its side. Position one of the Base Legs (38) on the base of the Upright (31) as shown. Make sure that the Base Leg Pads (41) and the Front Wheel (39) are in the indicated positions. Attach the Base Leg with two 3/8Ó x 2Ó Bolts (43), two 3/8Ó Washers (35) and two 3/8Ó Nuts (34). Carefully turn the treadmill onto its other side. Assemble the other Base Leg (38) as described. With the help of a second person, carefully raise the treadmill to the upright position so that both Base Legs (38) are resting flat on the floor. 1 39 31 34 43 35 41 38 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow step 2 on page 11 to lower the treadmill. Cut the plastic ties that hold the cage nuts in each Handrail (30, 32). Position the Left Handrail (30) on the left Upright (31) as shown. Thread a 1/4Ó x 1Ó Bolt (23) into the lower end of the Left Handrail. Thread a 1/4Ó x 1Ó Bolt (23) with a 1/4Ó Washer (51) into the upper end of left Upright and the Left Handrail. Do not tighten the Bolts yet. While a second person holds the Console Base (12) and the Right Handrail (32) near the right Upright (31), feed the excess Wire Harness (28) into the upper end of the Right Handrail, and pull it out of the bottom of the right Upright (31) (see drawing 5). Attach the Right Handrail (32) in the same way as the Left Handrail (30). Do not tighten the Bolts yet. Be careful not to pinch the Wire Harness (28). 2 23 51 31 28 12 23 51 32 30 31 23 23 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
Assembly requires two people.
Place all parts in a cleared area and remove the packing materials; do not
dispose of the packing materials until assembly is completed.
The following tools (not included) are required for assembly: two (2) adjustable wrenches
and a phillips screwdriver
.
Assembly will be more convenient if you have the following tools:
A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.
1.
Note that the Right Handrail and the Console Base
(not shown) are connected to the treadmill by a Wire
Harness.
During assembly steps 1 through 3, be
careful not to pull on or damage the Wire Harness.
With the help of a second person, carefully lay the
treadmill on its side. Position one of the Base Legs
(38) on the base of the Upright (31) as shown. Make
sure that the Base Leg Pads (41) and the Front
Wheel (39) are in the indicated positions. Attach the
Base Leg with two 3/8± x 2± Bolts (43), two 3/8±
Washers (35) and two 3/8± Nuts (34).
Carefully turn the treadmill onto its other side.
Assemble the other Base Leg (38) as described.
With the help of a second person, carefully raise the
treadmill to the upright position so that both Base
Legs (38) are resting flat on the floor.
2.
Refer to HOW TO LOWER THE TREADMILL FOR
USE on page 11. Follow step 2 on page 11 to lower
the treadmill.
Cut the plastic ties that hold the cage nuts in each
Handrail (30, 32).
Position the Left Handrail (30) on the left Upright (31)
as shown. Thread a 1/4± x 1± Bolt (23) into the lower
end of the Left Handrail. Thread a 1/4± x 1± Bolt (23)
with a 1/4± Washer (51) into the upper end of left
Upright and the Left Handrail.
Do not tighten the
Bolts yet.
While a second person holds the Console Base (12)
and the Right Handrail (32) near the right Upright
(31), feed the excess Wire Harness (28) into the
upper end of the Right Handrail, and pull it out of
the bottom of the right Upright (31) (see drawing 5).
Attach the Right Handrail (32) in the same way as
the Left Handrail (30).
Do not tighten the Bolts yet.
Be careful not to pinch the Wire Harness (28).
1
5
ASSEMBLY
43
35
41
38
39
31
34
2
51
31
31
12
28
32
30
51
23
23
23
23