Whirlpool GFG471LVB Owners Manual - Page 7

4. Replace the burner cap, making sure the alignment pins are properly aligned with the burner cap. A 5. Turn on the burner. If the burner does not light, check cap alignment. If the burner still does not light, do not service the sealed burner yourself. Contact a trained repair specialist. B A. Incorrect B. Correct OVEN USE Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled. IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and wellventilated room. Electronic Oven Controls Control Display The display will flash when powered up or after a power loss. Press CANCEL/OFF to clear. When oven is not in use, the time of day is displayed. Indicator lights show functions that are in use. Tones Tones are audible signals, indicating the following: One tone ■ Valid pad press ■ Oven is preheated (long tone) ■ Function has been entered ■ Reminder (on some models), repeating each minute after the end-of-cycle tones Three tones ■ Invalid pad press Four tones ■ End of cycle To Change Tone Settings: Tone Pitch Sets the pitch of the tone to either high or low. Press and hold BROIL for 5 seconds. "TONE PITCH HIGH" or "TONE PITCH LOW" will appear in the display. Press and hold BROIL again to change setting. To exit, press CANCEL/OFF. Key Press Tones Activates or turns off the tones when a keypad is pressed. Press and hold KEEP WARM for 5 seconds. "KEY PRESS TONES ON" or "KEY PRESS TONES OFF" will appear in the display. Press and hold KEEP WARM again to change setting. To exit, press CANCEL/OFF. End of Cycle Tone Activates or turns off the tones that sound at the end of a cycle. Press and hold CONVECT for 5 seconds. "CYCLE END TONE ON" or "CYCLE END TONE OFF" will appear in the display. Press and hold CONVECT again to change setting. To exit, press CANCEL/OFF. Reminder Tones Disable Turns off the short tones that sound 1 minute after the end of cycle tones. Press and hold BAKE for 5 seconds. "REMINDER TONES ON" or "REMINDER TONES OFF" will appear in the display. Press and hold BAKE again to change setting. To exit, press CANCEL/OFF. Audible Tones Disable Turns off all tones, including the end of cycle tone and key press tones. Reminder tones are still active when all tones are disabled. Press and hold CLOCK for 5 seconds. "ALL SOUNDS ON" or "ALL SOUNDS OFF" will appear in the display. Press and hold CLOCK again to change setting. To exit, press CANCEL/OFF. Fahrenheit and Celsius The temperature is preset at Fahrenheit, but can be changed to Celsius. To change: Press and hold PRECISE CLEAN for 5 seconds. A tone will sound, and "°C" or "°F" will appear on the display. Repeat to change back. To exit, press CANCEL/OFF. 12-Hour Shutoff The oven control is set to automatically shut off the oven 12 hours after the oven initiates a cook or clean function. This will not interfere with any timed or delay cook functions. Press and hold START TIME for 5 seconds to toggle to the 12-hour shutoff function. Scrolling text will display "12 HR SHUT-OFF ON" or "12 HR SHUT-OFF OFF." Press and hold to change setting. To exit, press CANCEL/OFF. Oven Temperature Control IMPORTANT: Do not use a thermometer to measure oven temperature because opening the oven door may cause element cycling to give incorrect readings. The oven provides accurate temperatures; however, it may cook faster or slower than your previous oven, so the temperature calibration can be adjusted. It can be changed in Fahrenheit or Celsius. To Adjust Oven Temperature Calibration: 1. Press and hold OVEN LIGHT for 5 seconds until the oven display shows the current calibration, for example "0°F. 2. Press the SET TEMP/TIME "+" or "-" arrow pads to increase or to decrease the temperature in 5°F (3°C) amounts. The adjustment can be set between 30°F (18°C) and -30°F (-18°C). 3. Press START. 7