Whirlpool WDF530PLYB Use & Care Guide - Page 15

Troubleshooting First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call. In the U.S.A., www.whirlpool.com In Canada, www.whirlpool.ca Dishwasher is not operating properly ■ Dishwasher does not run or stops during a cycle It is normal for certain cycles to repeatedly pause for several seconds during the main wash. Is the door closed tightly and latched? Is the right cycle selected? Is there power to the dishwasher? Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Has the motor stopped due to an overload? The motor automatically resets itself within a few minutes. If it does not restart, call for service. Is the water shutoff valve (if installed) turned on? ■ The Clean light is flashing Check the following: ■ Is the overfill protection float able to move up and down freely? Press down to release. ■ Be sure the water supply is turned on to the dishwasher. (This is very important following the new installation of your dishwasher.) ■ Check for suds in the dishwasher. If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill with water. Suds can come from: 1. Using the incorrect type of detergent, such as laundry detergent, hand soap, or dish detergent for hand washing dishes. 2. Forgetting to replace the rinse aid dispenser cap after filling (or refilling) the rinse aid. 3. Using an excessive amount of dishwasher detergent. ■ Dishwasher will not fill Is the overfill protection float able to move up and down freely? Press down to release. ■ Dishwasher seems to run too long Try the 1 Hour Wash cycle. Is the water supplied to the dishwasher hot enough? The dishwasher runs longer while heating water. Is the dishwasher cycle time within the cycle times? See cycle sections wash times. A delay automatically occurs in some wash and rinse cycles until the water reaches the proper temperature. This dishwasher is equipped with an optical sensor wash that detects water temperature, soil and detergent amount. Wash cycles are adjusted based on the load sensing. IMPORTANT: The very first wash cycle after installation in your home will be adjusted to include an additional 2 rinses. This cycle must not be interrupted for proper sensor adjustment. If this adjustment cycle is canceled or stopped before the Clean light comes on at the end of the cycle, the next wash cycle will repeat this sensor adjustment. ■ Water remains in the dishwasher Is the cycle complete? Was the disposer knockout plug removed during installation? (See "Install the drain hose" section in the Installation Instructions.) ■ Detergent remains in the covered section of the dispenser Is the cycle complete? Check for items such as cookie sheets, cutting boards, or large containers that may be blocking the detergent dispenser from opening properly. Be sure the cycle has finished (green light is on). If it has not finished, you will need to resume the cycle by pressing START/ RESUME and closing the door within 3 seconds. Is the detergent lump-free? Replace detergent if necessary. ■ White residue on the front of the access panel Was too much detergent used? Is the brand of detergent making excess foam? Try a different brand to reduce foaming and eliminate buildup. ■ Odor in the dishwasher Are dishes washed only every 2 or 3 days? Check and clean your filters regularly. See the table in "Filtration System" section for "Recommended Time Interval to Clean Your Filter." Does the dishwasher have a new plastic smell? Run a vinegar rinse as described in "Dishwasher Care." To avoid odor, use affresh™ dishwasher and disposal cleaner tablet once a month or as needed for a fresher dishwasher as described in "Dishwasher Care." ■ Condensation on the kitchen counter (built-in models) Is the dishwasher aligned with the countertop? Moisture from the vent in the dishwasher console can form on the counter. Refer to the Installation Instructions for more information. ■ Bottom rack does not fully slide into the dishwasher Check to see if items loaded for POWERSCOUR™ wash option have shifted. Reload to keep items from interfering with spray jets or spray arm. Dishes do not dry completely ■ Dishes do not dry completely Did you use a rinse aid? Your dishwasher is designed to use rinse aid for good drying performance. Without rinse aid your dishes and dishwasher interior will have excessive moisture. The heat dry option will not perform as well without rinse aid. ■ Dishes are not dry Did you load your dishwasher to allow proper water drainage? Do not overload. Use a liquid rinse aid to speed drying. Are the plastics wet? Plastics often need towel drying. Is the rinse aid dispenser empty? Did you use an air-dry or energy-saving dry option? Use a heated drying option for dryer dishes. ■ Excess moisture on racks and dishwasher interior Check the rinse aid indicator to see that there is rinse aid in the dispenser. Spots and stains on dishes ■ Spotting and filming on dishes Is your water hard, or is there a high mineral content in your water? Conditioning the final rinse water with a liquid rinse aid helps eliminate spotting and filming. Keep the rinse aid dispenser filled. Always use a high-temp option. If your water hardness is 13 grains or above, it is strongly recommended that you install a home water softener. If you do not wish to drink softened water, have the softener installed onto your hot water supply. 15