Whirlpool WDT780SAEM Use & Care Guide - Page 9
Controls And Cycle Status, Control, Purpose, Comments, Option Selections, Options - 24
View all Whirlpool WDT780SAEM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
OPTION SELECTIONS OPTIONS CAN BE SELECTED WITH WHAT IT DOES ADDED TIME TO CYCLE ADDED WATER GALLONS (LITERS) Sanitizes dishes and glassware in accordance with NSF International NSF/ANSI Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments. Only sanitizing cycles have been designed to meet the requirements of the NSF/ANSI 184 performance standard for soil removal and for sanitization efficacy. There is no intention, either directly or indirectly, that all cycles on a NSF/ANSI 184 certified dishwasher meet the NSF/ANSI 184 performance standard for soil removal and for sanitization efficacy. Sensor Heavy Normal Raises the main wash temperature to 135°F (57°C) and the final rinse temperature to 156°F (69°C). 0:05 to 1:06 0 to 3.86 (0 to 14.6) The Sanitize indicator glows at the end of the cycle if the Sani Rinse option was successfully completed. If the indicator does not activate, it is probably due to the cycle being interrupted. Dries dishes with heat. This option, with the use of Sensor Uses heating 0:08 to 0:46 0 rinse aid, will provide the best drying performance. Heavy element to speed Plastic items are less likely to deform when loaded in Normal drying times. the top rack. Use Heat Dry for optimum dry Soak & Clean Heat Dry option performance. Turn the Heat Dry option off for air dry. 1 - Hour Wash defaults to On when any cycle is selected except for 1-Hour Wash. Runs dishwasher at a later time. Select a wash cycle Available with Delays start of a 0:00 0 and options. Each time you press the delay button, it will display the next available delay time. Press any cycle cycle up to 24 hours. DELAY. Press START/RESUME. Close door firmly. NOTES: ■ The dishwasher remembers the last Delay you selected. To reset the delay time to something other than what is displayed, continue to press the Delay button until the desired delay time is reached. ■ Anytime the door is opened (such as, to add a dish); START/RESUME must be pressed again to resume delay countdown. Avoids unintended use of dishwasher between cycles, or cycle and option changes during a cycle. To turn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your dishwasher is locked, light flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked. To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off. NOTE: If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate whether Control Lock is active or not. CONTROLS AND CYCLE STATUS CONTROL PURPOSE COMMENTS Press to start or resume a wash cycle. If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED flashes. Cycle will not resume until door is closed and Start/Resume is pressed. NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3 seconds of pressing Start/Resume. If door is not closed within 3 seconds, Start/Resume button LED will flash, an audible tone will be heard (on some top control models), and cycle will not start. Press to cancel wash cycle. Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher drain completely. Press and hold START/RESUME for 3 seconds. 9