Home » Whirlpool Manuals » Laundry Dryers » Whirlpool WED6400SB » Manual Viewer

Whirlpool WED6400SB Installation Instructions - Page 1

Whirlpool WED6400SB - Cabrio 7.0 Cu Ft Capacity Electric Dryer Manual

UPC - 883049025094

View all Whirlpool WED6400SB manuals

Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

ELECTRIC DRYER INSTALLATION INSTRUCTIONS U.S.A. ONLY Para una version de estas instrucciones en español, visite www.Whirlpool.com TABLE OF CONTENTS TABLE OF CONTENTS 1 DRYER SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Optional Equipment 2 Location Requirements 3 ELECTRIC DRYER POWER HOOKUP 4 Electrical Requirements 4 Electrical Connection 5 VENTING 10 Venting Requirements 10 Plan Vent System 11 Install Vent System 12 INSTALL LEVELING LEGS 12 CONNECT VENT 12 CONNECT INLET HOSE (STEAM MODELS 13 LEVEL DRYER 13 COMPLETE INSTALLATION 13 Reverse Door Swing 14 TROUBLESHOOTING 15 Dryer Operation 15 Dryer Results 16 DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean: DANGER You can be killed or seriously injured if you don't immediately follow instructions. WARNING You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. W10267633A

Section	Page
ELECTRIC Dryer Installation Instructions U.S.A. Only	1
Para una version de estas instrucciones en español, visite www.Whirlpool.com	1
Table of Contents	1
Table of Contents 1	1
Dryer Safety 1	1
INSTALLATION REQUIREMENTS 2	1
Electric DRYER POWER HOOKUP 4	1
Venting 10	1
Install Leveling Legs 12	1
Connect Vent 12	1
Connect InLET HOSE (STEAM MODELS) 13	1
Level Dryer 13	1
Complete Installation 13	1
troubleshooting 15	1
Dryer Safety	1
INSTALLATION REQUIREMENTS	2
Tools and Parts	2
Parts supplied:	2
Non-Steam Models	2
Steam Models	2
A. Leveling legs (4)	2
B. “Y” connector	2
C. Short inlet hose	2
D. Inlet hose with right-angle connector	2
E. Rubber washer	2
Parts needed	2
Optional Equipment	2
Location Requirements	3
You will need	3
Installation clearances	3
Dryer Dimensions	3
Installation spacing for recessed area or closet installation	3
Recessed area	3
Side view- closet or confined area	3
Closet door with vents	3
Mobile home - Additional installation requirements	3
Mobile home installations require:	3
Electric DRYER POWER HOOKUP	4
Electrical Requirements	4
It is your responsibility	4
The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.	4
A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.	4
Electrical Connection	4
If using a power supply cord:	4
If your outlet looks like this:	4
If your outlet looks like this:	4
If connecting by direct wire:	4
Electrical Connection	5
1. Disconnect Power.	5
2. Remove hold-down screw and terminal block cover.	5
A. Terminal block cover	5
B. Hold-down screw	5
C. External ground conductor screw	5
D. Center, silver-colored terminal block screw	5
E. Neutral ground wire	5
F. Hole below terminal block opening	5
3. Install strain relief.	5
Style 1: Power supply cord strain relief	5
A. Strain relief tab pointing up	5
B. Hole below terminal block opening	5
C. Clamp section	5
D. Strain relief tab pointing down	5
Style 2: Direct wire strain relief	5
A. Removable conduit connector	6
B. Hole below terminal block opening	6
C. Strain relief threads	6
4. Now complete installation following instructions for your type of electrical connection:	6
4-wire (recommended)	6
3-wire (if 4-wire is not available)	6
Electrical Connection Options	6
If your home has:	6
And you will be connecting to:	6
Go to Section	6
4-wire connection: Power supply cord	6
A. 4-wire receptacle (NEMA type 14-30R)	6
B. 4-prong plug	6
C. Ground prong	6
D. Neutral prong	6
E. Spade terminals with upturned ends	6
F. 3/4\	6
G. Ring terminals	6
1. Remove center, silver-colored terminal block screw.	6
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.	6
A. Neutral ground wire.	6
B. Center, silver-colored terminal block screw	6
C. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver- colored terminal block screw	6
D. Neutral wire (white or center wire)	6
E. 3/4\	6
3. Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.	7
A. External ground conductor screw	7
B. Neutral ground wire	7
C. Ground wire (green or bare) of power supply cord	7
D. 3/4\	7
E. Center, silver-colored terminal block screw	7
F. Neutral wire (white or center wire)	7
4. Connect the other wires to outer terminal block screws. Tighten screws.	7
5. Tighten strain relief screws.	7
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	7
7. You have completed your electrical connection. Now go to “Venting Requirements.”	7
4-wire connection: Direct wire	7
1. Remove center, silver-colored terminal block screw.	7
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block....	7
A. Neutral ground wire.	7
B. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center, silver-colored terminal block screw	7
C. Center, silver-colored terminal block screw	7
D. Neutral wire (white or center wire)	7
E. 3/4\	7
3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.	7
A. External ground conductor screw	7
B. Neutral ground wire	7
C. Ground wire (green or bare) of power supply cable	7
D. 3/4\	7
E. Center, silver-colored terminal block screw	7
F. Neutral wire (white or center wire)	7
4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	8
5. Tighten strain relief screw.	8
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	8
7. You have completed your electrical connection. Now go to “Venting Requirements.”	8
3-wire connection: Power supply cord	8
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	8
A. 3-wire receptacle (NEMA type 10-30R)	8
B. 3-wire plug	8
C. Neutral prong	8
D. Spade terminals with up turned ends	8
E.3/4\	8
F. Ring terminals	8
G. Neutral (white or center wire)	8
1. Loosen or remove center, silver-colored terminal block screw.	8
2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.	8
A. External ground conductor screw	8
B. Neutral ground wire	8
C. Center, silver-colored terminal block screw	8
D. Neutral wire (white or center wire)	8
E. 3/4\	8
3. Connect the other wires to outer terminal block screws. Tighten screws.	8
4. Tighten strain relief screws.	8
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	8
6. You have completed your electrical connection. Now go to “Venting Requirements.”	8
3-wire connection: Direct wire	8
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	8
1. Loosen or remove center, silver-colored terminal block screw.	8
2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.	9
D. Neutral wire (white or center wire)	9
E. 3/4\	9
3. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	9
4. Tighten strain relief screw.	9
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	9
6. You have completed your electrical connection. Now go to “Venting Requirements.”	9
Optional 3-wire connection	9
Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.	9
1. Remove center, silver-colored terminal block screw.	9
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver- colored terminal block screw. Tighten screw.	9
A. External ground conductor screw	9
B. Neutral ground wire	9
C. Center, silver-colored terminal block screw	9
D. Neutral wire (white or center wire)	9
E. 3/4\	9
F. Grounding path determined by a qualified electrician	9
3. Connect the other wires to outer terminal block screws. Tighten screws.	9
4. Tighten strain relief screws.	9
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	9
6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.	9
Venting	10
Venting Requirements	10
If using an existing vent system	10
If this is a new vent system	10
Vent material	10
4\	10
Vent products can be purchased from your dealer or by calling Whirlpool Service. For more information, see the “Assistance or Service” section in your Use and Care Guide.	10
Rigid metal vent	10
Flexible metal vent	10
Elbows	10
45° elbows provide better airflow than 90° elbows.	10
Good	10
Better	10
Clamps	10
Clamp	10
Exhaust	10
Recommended:	10
A. Louvered hood style	10
B. Box hood style	10
Acceptable:	10
C. Angled hood style	10
Plan Vent System	11
Choose your exhaust installation type	11
Recommended exhaust installations	11
A. Dryer	11
B. Elbow	11
C. Wall	11
D. Exhaust hood	11
E. Clamps	11
F. Rigid metal or flexible metal vent	11
G. Vent length necessary to connect elbows	11
H. Exhaust outlet	11
Optional exhaust installations	11
Part Number W10186596 - all models	11
A. Standard rear offset exhaust installation	11
B. Left or right side exhaust installation	11
C. Bottom exhaust installation	11
Alternate installations for close clearances	11
A. Over-the-top installation (also available with one offset elbow)	11
B. Periscope installation	11
Part Number 4396028	11
Part Number 4396037 - 0\	11
Part Number 4396011 - 18\	11
Part Number 4396014 - 29\	11
Special provisions for mobile home installations	11
Determine vent path	12
Determine vent length and elbows needed for best drying performance	12
NOTE: Do not use vent runs longer than those specified in the Vent system chart.	12
Exhaust systems longer than those specified will:	12
Vent system chart	12
Number 90º elbows	12
Type of vent	12
Box /louvered hoods	12
Angled hoods	12
0	12
Rigid metal	12
1	12
Rigid metal	12
2	12
Rigid metal	12
3	12
Rigid metal	12
4	12
Rigid metal	12
Install Vent System	12
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.	12
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4\	12
3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the i...	12
Install Leveling Legs	12
1. To avoid damaging the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.	12
2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration.	12
3. Examine the leveling legs. Find the diamond marking.	12
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.	12
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.	12
Connect Vent	12
1. Using a 4\	12
2. Move dryer into its final location. Do not crush or kink vent.	12
3. Once the exhaust vent connection is made, remove the corner posts and cardboard.	12
Connect Inlet Hose (Steam Models)	12
1. Turn cold water faucet off and remove washer inlet hose.	12
2. Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the brass female end of the “Y” connector to the cold water faucet.	12
NOTE: If “Y” connector can be attached directly to cold water faucet, go to Step 6. If “Y” connector cannot be attached directly to the cold water faucet, the short hose must be used. Continue with Step 3.	12
3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.	12
4. Using pliers, tighten the couplings with an additional two-thirds turn.	13
NOTE: Do not overtighten. Damage to the coupling can result.	13
5. Attach “Y” connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.	13
6. Attach straight end of long hose to “Y” connector.	13
7. Attach washer cold inlet hose to other end of “Y” connector. Screw on coupling by hand until it is seated on connector.	13
8. Using pliers, tighten the couplings an additional two-thirds turn.	13
A. Inlet to cold water	13
NOTE: Do not overtighten. Damage to the coupling can result.	13
9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.	13
10. Using pliers, tighten the coupling an additional two-thirds turn.	13
NOTE: Do not overtighten. Damage to the coupling can result.	13
11. Check that the water faucets are on.	13
12. Check for leaks around “Y” connector, faucet, and hoses.	13
Level Dryer	13
Complete Installation	13
1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	13
2. Check that you have all of your tools.	13
3. Dispose of/recycle all packaging materials.	13
4. Check the dryer’s final location. Be sure the vent is not crushed or kinked.	13
5. Check that the dryer is level. See “Level Dryer.”	13
6. Remove the blue film on the console and any tape remaining on the dryer.	13
7. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.	13
8. Read “Dryer Use” in your Use and Care Guide.	13
9. For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on power.	13
Steam Models Only:	13
10. Be sure the water faucets are on.	13
11. Check for leaks around “Y” connector, faucet, and hoses.	13
12. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce p...	13
All Models:	14
13. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting.	14
If the dryer will not start, check the following:	14
Reverse Door Swing	14
1. Place a towel or soft cloth on top of dryer or work space to avoid damaging the surface.	14
Remove the door assembly	14
1. Open the dryer door.	14
2. Remove the bottom screw from each of the 2 hinges that attach dryer door to front panel of dryer.	14
3. Loosen the top screw from each of the 2 hinges in Step 2.	14
A. Loosen these screws.	14
B. Remove these screws.	14
4. Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel.	14
5. Remove the 4 plastic plugs located outside the dryer door opening.	14
6. Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4.	14
Reverse the strike	14
1. Remove the door strike from the dryer door opening.	14
2. Remove the cosmetic screw opposite the door strike.	14
A. Door strike	14
B. Cosmetic screw	14
3. Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were removed. NOTE: Door strike and plugs must be on the same side of the dryer door opening.	14
Reinstall the door	14
1. Remove the 4 screws and 2 hinges from the dryer door.	14
2. Replace the 4 screws in the same holes.	14
3. Remove the 4 screws from the opposite side of the door.	15
4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel.	15
5. Install screws in top hinge holes in the door. Do not tighten screws. Leave approximately 1/4\	15
6. Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws.	15
7. Close door to engage door strike.	15
troubleshooting	15
First try the solutions suggested here and possibly avoid the cost of a service call...	15
Dryer Operation	15
Dryer will not run	15
No heat	15
Dryer displaying code message	15
Try the following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit breaker.	16
Confirm the power cord is properly installed. Refer to “Electrical Connection” for details.	16
Select a Timed Dry heated cycle, and restart the dryer.	16
If the message persists, consult a qualified electrician.	16
If the message persists, have your entire home venting run cleaned.	16
Dryer Results	16

Match case Limit results 1 per page

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

U.S.A. ONLY

Para una version de estas instrucciones en español, visite www.Whirlpool.com

TABLE OF CONTENTS

..................................................................

DRYER SAFETY

..............................................................................

INSTALLATION REQUIREMENTS

................................................

Tools and Parts

............................................................................

Optional Equipment

.....................................................................

Location Requirements

................................................................

ELECTRIC DRYER POWER HOOKUP

.........................................

Electrical Requirements

...............................................................

Electrical Connection

...................................................................

VENTING

........................................................................................

Venting Requirements

................................................................

Plan Vent System

.......................................................................

Install Vent System

.....................................................................

INSTALL LEVELING LEGS

...........................................................

CONNECT VENT

...........................................................................

CONNECT INLET HOSE (STEAM MODELS)

..............................

LEVEL DRYER

..............................................................................

COMPLETE INSTALLATION

.......................................................

Reverse Door Swing

...................................................................

TROUBLESHOOTING

.................................................................

Dryer Operation

..........................................................................

Dryer Results

..............................................................................

W10267633A

DRYER SAFETY

You

You can be kille

or seriously injure

if you

on't imme

iately

can be kille

or seriously injure

if you

on't follow

All

afety me

age

will tell you what the potential hazard i

, tell you how to reduce the chance of injury, and tell you what can

happen if the in

truction

are not followed.

Your safety an

the safety of others are very important.

We have provided many important

afety me

age

in thi

manual and on your appliance. Alway

read and obey all

afety

age

Thi

the

afety alert

ymbol.

Thi

ymbol alert

you to potential hazard

that can kill or hurt you and other

All

afety me

age

will follow the

afety alert

ymbol and either the word “DANGER” or “WARNING.”

The

e word

mean:

follow instructions.

instructions.

DANGER

WARNING