Whirlpool WEG750H0H Owners Manual - Page 11

Cooktop

Get Whirlpool WEG750H0H PDF manuals and user guides View all Whirlpool WEG750H0H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

COOKTOP WARNING A B C Fire Hazard Do not let the burner flame extend beyond the edge of the pan. Turn off all controls when not cooking. Failure to follow these instructions can result in death or fire. Electric igniters automatically light the surface burners when control knobs are turned to Ignite. Before setting a control knob, place filled cookware on the grate. Do not operate a burner using empty cookware or without cookware on the grate. To Use: 1. Push in and turn knob counterclockwise to Ignite. All surface burners will click. Only the burner with the control knob turned to Ignite will produce a flame. 2. Turn knob to anywhere between HIGH and LOW. REMEMBER: When range is in use, the entire cooktop area may become hot. Power Failure In case of prolonged power failure, the surface burners can be lit manually. Hold a lit match near a burner, and then turn knob counterclockwise to Ignite. After burner lights, turn knob to setting. Surface Burners IMPORTANT: Do not obstruct the flow of combustion and ventilation air around the burner grate edges. Burner Cap: Always keep the burner cap in place when using a surface burner. A clean burner cap will help avoid poor ignition and uneven flames. Always clean the burner cap after a spillover, and routinely remove and clean the caps according to the "General Cleaning" section. NOTE: Each round burner base is marked with a letter indicating the burner size. Alignment: Be sure to align the gas tube opening in the burner base with the orifice holder on the cooktop and the igniter electrode with the notch in the burner base. NOTE: Each round burner base is marked with a letter indicating the burner size. E D A. Burner cap B. Gas tube opening C. Burner base D. Igniter electrode E. Orifice holder Gas Tube Opening: Gas must flow freely throughout the gas tube opening for the burner to light properly. Keep this area free of soil, and do not allow spills, food, cleaning agents, or any other material to enter the gas tube opening. Keep spillovers out of the gas tube opening by always using a burner cap. A B A. 1" to 11/2" (2.5 cm to 3.8 cm) B. Burner ports Burner Ports: Check burner flames occasionally for proper size and shape as shown in the previous illustration. A good flame is blue in color, not yellow. Keep this area free of soil, and do not allow spills, food, cleaning agents, or any other material to enter the burner ports. To Clean: IMPORTANT: Before cleaning, make sure all controls are off and the cooktop is cool. Do not use oven cleaners, bleach, or rust removers. Do not wash in the dishwasher. 1. Remove the burner cap and the burner base, and clean according to the "General Cleaning" section. 2. Clean the gas tube opening with a damp cloth. 3. Clean clogged burner ports with a straight pin as shown. Do not enlarge or distort the port. Do not use a wooden toothpick. If the burner needs to be adjusted, contact a trained repair specialist. 04-Dec-2017 14:02:55 EST | RELEASED In some European1f1actories the letter "W" of the part code mentioned herein will be automatically replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
11
COOKTOP
Electric igniters automatically light the surface burners
when control knobs are turned to Ignite.
Before setting a control knob, place filled cookware on
the grate. Do not operate a burner using empty cookware
or without cookware on the grate.
To Use:
1.
Push in and turn knob counterclockwise to Ignite.
All surface burners will click. Only the burner with the
control knob turned to Ignite will produce a flame.
2.
Turn knob to anywhere between HIGH and LOW.
Power Failure
In case of prolonged power failure, the surface burners can
be lit manually. Hold a lit match near a burner, and then turn
knob counterclockwise to Ignite. After burner lights, turn
knob to setting.
Surface Burners
IMPORTANT:
Do not obstruct the flow of combustion
and ventilation air around the burner grate edges.
Burner Cap:
Always keep the burner cap in place when using
a surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover,
and routinely remove and clean the caps according to the
“General Cleaning” section.
NOTE:
Each round burner base is marked with a letter indicating
the burner size.
Alignment:
Be sure to align the gas tube opening in the burner
base with the orifice holder on the cooktop and the igniter
electrode with the notch in the burner base.
NOTE:
Each round burner base is marked with a letter indicating
the burner size.
Gas Tube Opening:
Gas must flow freely throughout the gas
tube opening for the burner to light properly. Keep this area free
of soil, and do not allow spills, food, cleaning agents, or any other
material to enter the gas tube opening. Keep spillovers out of the
gas tube opening by always using a burner cap.
Burner Ports:
Check burner flames occasionally for proper size
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil, and do not
allow spills, food, cleaning agents, or any other material to enter
the burner ports.
To Clean:
IMPORTANT:
Before cleaning, make sure all controls are off
and the cooktop is cool. Do not use oven cleaners, bleach, or
rust removers. Do not wash in the dishwasher.
1.
Remove the burner cap and the burner base, and clean
according to the “General Cleaning” section.
2.
Clean the gas tube opening with a damp cloth.
3.
Clean clogged burner ports with a straight pin as shown.
Do not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact
a trained repair specialist.
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER:
When range is in use, the entire cooktop area
may become hot.
A
B
C
D
E
A. Burner cap
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Orifice holder
B
A
A. 1" to 1
1
/
2
" (2.5 cm to 3.8 cm)
B. Burner ports
04-Dec-2017 14:02:55 EST | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")