Whirlpool WFG361LVS Installation Instructions - Page 17

To Convert Surface Burners, To Convert Oven Bake Burner - btu

Page 17 highlights

To Convert Surface Burners 1. Remove burner cap. 2. Using a Phillips or Quadrex® screwdriver, remove the burner base. NOTE: Reinstall one of the screws through the range cooktop to hold the orifice spud holder in place while removing and replacing the orifice spuds. C A D B A. Igniter electrode B. Gas tube opening C. Burner cap D. Burner base 3. Apply masking tape to the end of a 7 mm nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. C A D B Refer to the following chart for the correct Natural gas orifice spud placement. Natural Gas Orifice Spud Chart Burner Rating Color Size ID Number 17,000 BTU 15,500 BTU 14,200 BTU 13,000/13,500 BTU 12,000/12,500 BTU 9,500 BTU 8,000 BTU 5,000 BTU Red/Magenta Red/Black Red/Orange Red/Blue Red/Yellow Red/Brown Red/White Red/Brass 2.10 mm 2.00 mm 1.90 mm 1.85 mm 1.80 mm 1.55 mm 1.40 mm 1.10 mm N210 N200 N190 N185 N180 N155 N140 N110 NOTE: Refer to the Model Number and Serial Number Plate located on the oven frame behind the top left side of the oven door for proper sizing of spuds for each burner location. 5. Place LP gas orifice spuds in plastic parts bag for future use and keep with package containing literature. 6. Replace the burner base using both screws. 7. Replace burner cap. 8. Repeat steps 1-7 for the remaining burners. To Convert Oven Bake Burner 1. Remove oven racks. 2. Use a ½" combination wrench to loosen the orifice hood away from the pin (about 2 to 2½ turns). The oven bake burner flame cannot be properly adjusted if this conversion is not made. See "Adjust Oven Bake Burner Flame" in the "Electronic Ignition System" section. A B A A. Orifice spud B. Orifice spud holder C. Screw D. Spark electrode 4. Gas orifice spuds are stamped with a number on the side. Replace the LP gas orifice spud with the correct Natural gas orifice spud. A A. Orifice hood B. Pin XXX A A. Stamped number 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

17
To Convert Surface Burners
1.
Remove burner cap.
2.
Using a Phillips or Quadrex
®
screwdriver, remove the burner
base.
NOTE:
Reinstall one of the screws through the range cooktop
to hold the orifice spud holder in place while removing and
replacing the orifice spuds.
3.
Apply masking tape to the end of a 7 mm (
⁹⁄₃₂
") nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and
remove by turning it counterclockwise and lifting out. Set gas
orifice spud aside.
4.
Gas orifice spuds are stamped with a number on the side.
Replace the LP gas orifice spud with the correct Natural gas
orifice spud.
Refer to the following chart for the correct Natural gas orifice
spud placement.
Natural Gas Orifice Spud Chart
NOTE:
Refer to the Model Number and Serial Number Plate
located on the oven frame behind the top left side of the oven
door for proper sizing of spuds for each burner location.
5.
Place LP gas orifice spuds in plastic parts bag for future use
and keep with package containing literature.
6.
Replace the burner base using both screws.
7.
Replace burner cap.
8.
Repeat steps 1-7 for the remaining burners.
To Convert Oven Bake Burner
1.
Remove oven racks.
2.
Use a ½" combination wrench to loosen the orifice hood
away from the pin (about 2 to 2½ turns). The oven bake
burner flame cannot be properly adjusted if this conversion is
not made. See “Adjust Oven Bake Burner Flame” in the
“Electronic Ignition System” section.
A. Igniter electrode
B. Gas tube opening
C. Burner cap
D. Burner base
A. Orifice spud
B. Orifice spud holder
C. Screw
D. Spark electrode
A. Stamped number
A
B
C
D
B
A
C
D
XXX
A
Burner Rating
Color
Size
ID
Number
17,000 BTU
15,500 BTU
14,200 BTU
13,000/13,500 BTU
12,000/12,500 BTU
9,500 BTU
8,000 BTU
5,000 BTU
Red/Magenta
Red/Black
Red/Orange
Red/Blue
Red/Yellow
Red/Brown
Red/White
Red/Brass
2.10 mm
2.00 mm
1.90 mm
1.85 mm
1.80 mm
1.55 mm
1.40 mm
1.10 mm
N210
N200
N190
N185
N180
N155
N140
N110
A. Orifice hood
B. Pin
A
B
A
A