Whirlpool WFW9151YW Installation Guide - Page 2

Installation Requirements - pedestal

Page 2 highlights

INSTALLATION REQUIREMENTS Tools and Parts Gather required tools and parts before starting installation. Parts needed: (Not supplied with washer) Tools needed: Adjustable or open end wrenches 1⁄2" (13 mm) and 9⁄16" (14 mm) 4" min (102 mm) Level Wood block Ruler or measuring tape Pliers that open to 19⁄16" (39.5 mm) Parts supplied: NOTE: All parts supplied for installation are in the washer basket. Beaded tie strap Drain hose Drain hose form and hose clamp Optional tools: Transport bolt hole plugs (Quantity will vary, depending on model.) Flashlight 2 Bucket Inlet hoses (2) with washers (4) Alternative Inlet Hoses: (may be required for some installations, not supplied with washer) n 8212656RP 10 ft (3.0 m) Inlet hose, Black EPDM (2 pack) n 8212641RP 5 ft (1.5 m) Inlet hose, Black EPDM (2 pack) n 8212546RP 4 ft (1.2 m) Inlet hose, Black EPDM (2 pack) n 8212545RP 5 ft (1.5 m) Inlet hose, Red and Blue EPDM (2 pack) n 8212487RP 5 ft (1.5 m) Nylon braided inlet hose (2 pack) n 8212638RP 6 ft (1.8 m) Nylon braided inlet hose, space saving 90° elbow, hypro-blue steel couplings (2 pack) n 8212637RP 6 ft (1.8 m) Inlet hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack) Available Accessories: An optional matching pedestal is available for your washer. Please contact your retailer for ordering information, or see the Assistance or Service page on the back of your Use and Care Guide. Alternative parts (Not supplied with washer) Your installation may require additional parts. To order, please refer to toll-free numbers on the back page of your Use and Care Guide. If you have: You will need: Laundry tub or standpipe taller than 96" (2.4 m) Sump pump system (if not already available) Overhead sewer Standard 20 gal. (76 L) 30" (762 mm) tall drain tub or utility sink and sump pump (available from local plumbing suppliers) 1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connect Kit Part Number 285835 Floor drain system Siphon Break Part Number 285834; additional Drain Hose, Part Number 8318155; and Connector Kit, Part Number 285835 Drain hose too short Extension Drain Hose Part Number 285863 Water faucets beyond reach of fill hoses 2 longer water fill hoses; 6 ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

2
Optional tools:
Parts supplied:
NOTE:
All parts supplied for installation are in the washer
basket.
4" min
(102 mm)
Wood block
Adjustable or open end
wrenches
1
2
" (13 mm) and
9
16
" (14 mm)
Ruler or measuring tape
Level
Pliers that open to 1
9
16
"
(39.5 mm)
Flashlight
Bucket
Beaded tie strap
Drain hose
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
Transport bolt hole
plugs (Quantity will vary,
depending on model.)
Alternative Inlet Hoses:
(may be required for some installations, not supplied
with washer)
n
8212656RP
10 ft (3.0 m) Inlet hose, Black EPDM (2 pack)
n
8212641RP
5 ft (1.5 m) Inlet hose, Black EPDM (2 pack)
n
8212546RP
4 ft (1.2 m) Inlet hose, Black EPDM (2 pack)
n
8212545RP
5 ft (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP
5 ft (1.5 m) Nylon braided inlet hose (2 pack)
n
8212638RP
6 ft (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
n
8212637RP
6 ft (1.8 m) Inlet hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Available Accessories:
An optional matching pedestal is available for your washer.
Please contact your retailer for ordering information, or see
the Assistance or Service page on the back of your Use and
Care Guide.
Alternative parts
(Not supplied with washer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on the back page of your Use and
Care Guide.
If you have:
You will need:
Laundry tub or
Sump pump system
standpipe taller than
(if not already available)
96" (2.4 m)
Overhead sewer
Standard 20 gal. (76 L) 30" (762 mm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
1" (25 mm) standpipe
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connect Kit Part Number 285835
Floor drain system
Siphon Break Part Number 285834;
additional Drain Hose,
Part Number 8318155; and Connector
Kit, Part Number 285835
Drain hose too short
Extension Drain Hose
Part Number 285863
Water faucets beyond
2 longer water fill hoses;
reach of fill hoses
6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008
Drain hose form and hose
clamp
Inlet hoses (2) with
washers (4)
Parts needed:
(Not supplied with washer)