Yamaha CC-70S Owner's Manual - Page 13

Speaker connection, Connecting the AC supply lead, PREPARATION FOR USE

Page 13 highlights

PREPARATION FOR USE For connecting with NX-S70 (Black wire with white line → plus (+) terminal, black wire → minus (-) terminal) Speaker connection Connect each speaker wire to the SPEAKERS terminals. Cautions • Do not let the bare speaker wires touch each other as this could damage the receiver and/or speakers. • When connecting the speakers to the unit, be sure to connect the speaker wires properly. Do not mistake the right channel for the left channel and the plus (+) terminal for the minus (-) terminal. • [For U.S.A., Canada, Australia and General models] Do not connect these SPEAKERS terminals to speakers other than the provided speaker system NX-S70. • [For U.K. and Europe models] Set the SPEAKERS SELECTOR switch on the rear panel of the receiver to the proper position before connections. If you use YAMAHA Active Servo Processing Speaker System NX-S70, set this switch to "NX-S70". If you use a speaker system other than NX-S70, set this switch to "CONVENTIONAL". System connection • Connect the red connector on the rear of CDC-S90 to the red socket on the rear of RX-S70. • Connect the black connector on the rear of KXW-S70 (or KX-S90) to the black socket. How to disconnect the system connector Grasp both sides of the connector to disconnect the connector. To an AC outlet Connecting the AC supply lead • After connecting the speakers and system connectors, plug the AC supply lead into a convenient AC outlet. • Unplug the AC supply lead from the AC outlet if the unit is not to be used for a long period of time. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51

11
Speaker connection
Connect each speaker wire to the SPEAKERS terminals.
Cautions
Do not let the bare speaker wires touch each other as this
could damage the receiver and/or speakers.
When connecting the speakers to the unit, be sure to
connect the speaker wires properly. Do not mistake the
right channel for the left channel and the plus (+) terminal
for the minus (–) terminal.
[For U.S.A., Canada, Australia and General models]
Do not connect these SPEAKERS terminals to speakers
other than the provided speaker system NX-S70.
[For U.K. and Europe models]
Set the SPEAKERS SELECTOR switch on the rear panel
of the receiver to the proper position before connections.
If you use YAMAHA Active Servo Processing Speaker
System NX-S70, set this switch to “NX-S70”.
If you use a speaker system other than NX-S70, set this
switch to “CONVENTIONAL”.
System connection
Connect the red connector on the rear of CDC-S90 to the
red socket on the rear of RX-S70.
Connect the black connector on the rear of KXW-S70 (or
KX-S90) to the black socket.
How to disconnect the system connector
Grasp both sides of the connector to disconnect the
connector.
Connecting the AC supply lead
After connecting the speakers and system connectors,
plug the AC supply lead into a convenient AC outlet.
Unplug the AC supply lead from the AC outlet if the unit is
not to be used for a long period of time.
PREPARATION FOR USE
For connecting with NX-S70
(Black wire with white line
plus (+) terminal,
black wire
minus (–) terminal)
To an AC outlet